Makita BCL142 Bedienungsanleitung Seite 7

cartridge.
To insert the battery cartridge, align the tongue on
•
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can
see the red part on the upper side of the button, it
is not locked completely. Insert it fully until the red
part cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone
around you.
Do not use force when inserting the battery
•
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
Battery protection system
The cleaner is equipped with the protection system,
which automatically cuts off the output power for its long
service life.
The cleaner stops during operation when the cleaner
and/or battery are placed under the following situation.
This is caused by the activation of protection system and
does not show the cleaner trouble.
When the cleaner is overloaded:
•
At this time, release the switch trigger and
remove causes of overload and then pull the
switch trigger again to restart.
When the remaining battery capacity gets low:
•
Recharge the battery cartridge.
Switch action
Fig.3
To start the cleaner, simply press the "HIGH/LOW"
button. To switch off, press the "OFF" button. To change
the cleaner speed, press the "HIGH/LOW" button. The
first press on this button is for high speed and the
second press for low speed and then each press on this
button repeats the high/low speed cycle alternatively.
Battery power lamp
Fig.4
When the remaining battery capacity gets low, the
•
battery power lamp blinks.
When the remaining battery capacity gets much
•
lower, the tool stops during operation and the
battery power lamp lights up for about ten seconds.
At this time, remove the battery cartridge from the
tool and charge it .
NOTE:
The time at which the battery power lamp start
•
blinking or lighting up depends on the temperature
at work place and the battery cartridge conditions.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before carrying out
any work on the tool.
Disposing of Dust
CAUTION:
Empty the cleaner before it becomes too full, or the
•
suction force weakens.
Be sure to empty out the dust inside the cleaner
•
itself. Failure to do so may cause the sponge filter
to be clogged or the motor to be damaged.
Never throw away the dust stopper because it
•
should be used whenever either the dust bag or
the dust pack is used.
Fig.5
1. Push the button to open the front cover. Opening
it until a click is heard allows a positive stop at that
position.
Fig.6
NOTE:
The cleaner is constructed in such a way that the
•
front cover comes off when trying to force the front
cover open at the angle of more than 90°. If the
front cover comes off, insert it into the front cover
joint in place.
CAUTION:
When closing the front cover, be careful not to
•
pinch your fingers.
Fig.7
2. Pull out both the orange-colored dust stopper and
dust bag together at the same time.
Fig.8
Fig.9
3. Remove the dust stopper and empty the cleaner.
Dust bag and paper pack
Install either dust bag or paper pack before using
cleaner.
Use the dust stopper when installing either dust bag or
paper pack.
Dust bag are usable many times repeatedly by cleaning
it out.
Paper pack is a throw-away type. Throw away the entire
paper pack without emptying when it has become full.
Installing dust bag
Fig.10
Use the dust stopper when installing dust bag. Be
careful not to take the upper side for the lower side by
mistake because they are different each other.
Fig.11
1. Insert the protrusion of the dust bag into the
groove in the dust stopper as shown in the figure.
Fig.12
2. There is no distinction between the upper and
lower sides of the dust bag. You may insert its
protrusion of any side into the lower groove of the
dust stopper.
7