Clarion DXZ788RUSB Bedienungsanleitung Seite 19

01_DXZ788RUSB_EN.book 19 ページ ２００７年１１月２７日 火曜日 午後６時３４分
Basic Operations
Adjusting Sound Setting
Mode
To change sound setting mode
1. Press and hold the [
seconds or longer and select the sound
setting mode to adjust.
2. Push the [SEEK PANEL] leftward or
rightward to select the "item name".
When speaker system is "NORMAL":
"PRESET" "ALL SEAT"
ALIGNMENT" "P.EQ ON/OFF"
SELECT" "SUB WOOFER"
"PRESET"...
When speaker system is "3WAY":
"PRESET" "ALL SEAT"
"T ALIGNMENT"
"P.EQ ON/OFF"
"SUB WOOFER" "PRESET"...
When speaker system is "2WAY":
"PRESET" "ALL SEAT"
"T ALIGNMENT"
"P.EQ ON/OFF"
"PRESET"...
∗ In the case of item names appearing with
the "ENT" suffix, after the item name, the
[ ] button must be pressed to display
the setting value.
∗ After completing settings, press the
button to return to the previous mode.
Setting the preset setting
This function allows you to recall, save or
initialize the sound settings.
If your speaker system is "3WAY" or "2WAY",
you can store and recall up to three adjustments
you have made to "P.EQ ON/OFF", "X-OVER",
"T ALIGNMENT", "SPEAKER GAIN".
LOAD: To recall the stored sound settings.
SAVE: To save the sound settings.
INITIAL: To initialize the sound settings.
The load and the save can be adjusted as
follows.
2-1. Select "PRESET".
3-1. Press the [ ] button.
3-2. Push the [SEEK PANEL] leftward or
rightward and select from:
"LOAD" "SAVE"
"LOAD"...
] button for 2
"T
"EQ
"X-OVER"
"SPEAKER GAIN"
"EQ SELECT"
"X-OVER"
"SPEAKER GAIN"
"EQ SELECT"
[ ]
"INITIAL"
3-3. Push the [P.CH] button upward or
downward to adjust the load and the save.
LOAD : "SELECTING 1" to "SELECTING
3" (The factory default setting is
"SELECTING 1")
SAVE : "1" to "3" (The factory default
setting is "1")
3-4. Press and hold the [
store into memory.
(LOAD: Press and hold the button for 1
second or longer.
SAVE: Press and hold the button for 2
seconds or longer.)
Setting the all seat
The setting of "T ALIGNMENT" and "SPEAKER
GAIN" temporarily returns to the factory default
setting. When the setting that is adjusted for the
driver's seat returns to the factory default
setting, a sound suitable for all seats is
provided.
∗ The factory default setting is "OFF".
2-1. Select "ALL SEAT".
3-1. Push the [P.CH] button upward or
downward to select "ON" or "OFF".
Setting the X-OVER
This function allows you to adjust the speaker
setting such as cutoff frequencies or slope
matched to the speakers you are using.
(Crossover).
2-1. Select "X-OVER".
3-1. Press the [ ] button.
3-2. Push the [SEEK PANEL] leftward or
rightward and select from:
3WAY mode
• HIGH
(Front speaker (high))
• HPF
(High pass filter)
• HPF SLOPE
(HPF slope)
• PHASE
(Phase)
• MID
(Front speaker (mid))
• LPF
(Low pass filter)
• LPF SLOPE
(LPF slope)
• HPF
• HPF SLOPE
] button to
• PHASE
• SUB-W
(Subwoofer)
• LPF
• LPF SLOPE
• HPF
• HPF SLOPE
• PHASE
• HIGH
19
DXZ788RUSB