Selecting Pty - Clarion CZ109EL Bedienungsanleitung

01_CZ109EL_ENG.book Page 10 Thursday, May 21, 2009 5:05 PM
● Setting the TA standby mode
If you press the [TA] button when only
appears in the display,
"TP
the display and the unit is set into the TA
standby mode until a traffic announcement is
broadcast. When a traffic announcement
broadcast starts, "TRA INFO" appears in the
display. If you press the [TA] button while a
traffic announcement broadcast is being
received, the traffic announcement broadcast
reception is cancelled and the unit goes into the
TA standby mode.
● Cancelling the TA standby mode
As "TP " and "TA" appears in the display, press
the [TA] button. The "TA" in the display goes off
and the TA standby mode is cancelled.
∗ If "TP" is not appeared, pressing the [TA] button
searches for a TP station.
● Searching for a TP station
When "TP " is not appeared, if you press the [TA]
button, "TA" appears in the display and the unit
automatically receives a TP station.
Auto store function for TP stations
You can automatically store up to 6 TP stations
into preset memory. If the number of TP can be
received less than 6, broadcast stations already
stored in memory and left without being
overwritten.
As "TA" appears in the display, press and hold
the [ ] button (2 sec.). The TP stations with
the good reception sensitivity are stored into
preset memory.
∗ Even if you select FM1 or FM2, a TP station is
stored in memory for FM3.
PTY (Programme Type)
This function enables you to listen to a
broadcast of the selected programme type even
if the unit is on a function mode other than radio.
∗ Some countries do not yet have PTY broadcast.
∗ In the TA standby mode, a TP station has priority
over a PTY broadcast station.
∗ The factory default setting is "OFF".
1. Press and hold the [DISP] button (1 sec.) to
switch to the RDS adjustment selection
display.
2. Press [x] or [v] to select "PTY".
3. Turn the [ROTARY] knob to select "ON" or
"OFF".
10
CZ109EL
"
"TP
" and "TA" appear in
• ON:
"PTY" appears in the display and PTY
standby mode is enabled. When the selected
PTY broadcast starts, the PTY item name
appears in the display.
• OFF:
"PTY" turns off in the display and PTY
standby mode is cancelled.
4. Press the [DISP] button to return to the
previous mode.
● Cancelling a PTY interrupt broadcast
Press the [SRC] button during the PTY interrupt
broadcast, the PTY interrupt is cancelled and
the unit returns to PTY standby mode.

Selecting PTY

1. Press and hold the [DISP] button (1 sec.) to
switch to the RDS adjustment selection
display.
2. Press [x] or [v] to select "PTY SEL".
3. Press the [ ] button.
4. Press any of the [DIRECT] buttons.
Alternatively, turn the [ROTARY] knob to
select the desired PTY.
5. Press the [DISP] button to return to the
previous mode.
∗ 6 types of PTY are stored for the [DIRECT]
buttons.
∗ The PTY select mode is cancelled
automatically 7 seconds after a PTY is
selected.
PTY seek
1. Press and hold the [DISP] button (1 sec.) to
switch to the RDS adjustment selection
display.
2. Press [x] or [v] to select "PTY SEL".
3. Press the [ ] button.
4. Press the [v] button to search for a PTY
broadcast in the direction of higher
frequencies; press the [x] button to search
in the direction of lower frequencies.
∗ If no station with the selected PTY broadcast
can be received, the unit returns to the PTY
select mode.