Recommended Settings; Saving Energy; Maintenance And Care; What To Do If - AEG DDLE ÖKO TD 27 Bedienung Und Installation

Operation
4.3 Resetting to factory defaults
Anti-scalding protection and self-learning remote temperature control are not reset.
Factory defaults (see chapter "Specification").
4.4 Remote temperature control operation
Remote temperature control operation
OFF
3s
You can switch the appliance heating system to OFF using the mini wireless remote control. To do so, press and hold the
minus button for ≥ 3 seconds. Press any button to switch it back on.

4.5 Recommended settings

4.5.1 Saving energy

The following recommended settings will result in the low-
est energy consumption:
◦ 38 °C for hand washbasins, showers, bath
◦ 55 °C for kitchen sinks.
4.5.2 Thermostatic valve
If you operate the appliance with a thermostatic valve,
we would recommend that you set the temperature at the
appliance to the maximum level (temperature selector at
60 °C). You can then select the required temperature at
the thermostatic valve.

5. Maintenance and care

A damp cloth is sufficient for cleaning the casing. Never
use abrasive or corrosive cleaning agents.

6. What to do if ...

6.1 ... the water supply was interrupted
Risk of damage
!
After an interruption to the water supply, take the
following steps prior to returning the appliance into
use.
» Remove fuses or trip the appropriate MCBs.
» Open a draw-off valve, downstream of the appliance,
long enough to vent all air from the appliance and its
upstream cold water supply line.
» Replace the fuses or reset the relevant MCBs.
6.2 ..... the remote temperature control
batteries are empty
Fault Cause
LED on remote tem- Batteries in the re-
perature control flash- mote temperature
es during and after control spent.
sending.
» Open the remote temperature control casing by un-
doing the two screws at the back and pivoting the
casing open.
» Remove the battery and insert a new one, type CR
2032.
Note
The positive terminal of the battery must face away
from the PCB.
28
»
Press button 1 and button 2 simultaneously for two
seconds.
»
Press 38°
»
Press 55°
»
Press +
»
Press -
" Remedy
Replace the battery.
Display flashes to confirm.
38 °C
55 °C
Press 1x: Set value raised by 0.5 °C.
Press 1x: Set value lowered by 0.5 °C.
» Close the casing. Observe the casing recess in the
edge of the lid. The recess determines the correct
positioning of the lid and ensures the casing is tightly
sealed.
Battery disposal
Never dispose of batteries with domestic waste.
Spent batteries may contain noxious substances
that can be detrimental to the environment and
human health. Dispose of spent batteries through
your dealer or via a central recycling point for spe-
cial waste.
6.3 ... the appliance develops faults
Fault Cause
The heating system No power.
will not start in spite
of the tap being fully
open.
Flow rate to low,
shower head/aerators
scaled up.
Heater is faulty.
Intermittent cold The air sensor detects
water. air in the water and
briefly switches the
heater off.
Flow rate too low. ECO mode is activat-
ed and the flow rate
value in ECO mode is
set too low.
Shower head/aerators
scaled up.
Temperatures above Dynamic anti-scalding
43 °C cannot be se- protection is enabled.
lected.
Where a fault can only be remedied by a contractor, he
can better and more speedily remedy the fault if you pro-
vide him with some of the details from the type plate (19):
DDLE ÖKO TD No.: . . . -
Remedy
Check the fuses/
MCBs in your fuse
box/distribution board.
Clean and/or descale
the aerators.
Call customer service
/ your contractor.
Appliance starts again
after one minute.
Set a higher ECO flow
rate.
Clean and/or descale
the aerators.
Is cancelled automati-
cally two minutes after
drawing has ceased.
19
. . .
. - . . . . . .