Call Button - Sony HDLA1500 Handbuch

Note
When one of the CURSOR buttons is lit, the H-POSI, V-
POSI, WIDTH, and HEIGHT buttons do not function.
e CURSOR STORE button
Press this button to store the size and position of the box
cursor in memory.
Note
If the CURSOR ON button is not lit, box cursor
information will not be stored.
f CURSOR ON button
When this button is pressed, the button will light up and the
box cursor will be displayed on the viewfinder screen.
When the button is pressed again, the light will go off and
the box cursor will disappear.
g H-POSI (horizontal position) control
Adjust the horizontal position of the box cursor displayed
on the viewfinder screen within the effective resolution
area.
h V-POSI (vertical position) control
Adjust the vertical position of the box cursor displayed on
the viewfinder screen within the effective resolution area.
i WIDTH control
Adjust the width of the box cursor displayed on the
viewfinder screen within the effective resolution area.
j HEIGHT control
Adjust the height of the box cursor displayed on the
viewfinder screen within the effective resolution area.
k FILTER LOCAL (filter local control) button
Pressing and lightening this button enables selecting of a
color temperature conversion filter and ND filter using the
1)
CC filter selector and ND filter selector. Pressing the
button again (it goes dark) gives control of the filters to the
MSU-900/950 Master Setup Unit or RCP-700/900-series
Remote Control Panel.
1) Invalid when the HDC1400 is mounted
l Filter selectors
When the FILTER LOCAL button is lit up, you can change
the ND filter and CC (color temperature conversion) filter
settings.
Turn the left selector to select an ND filter and the right
1)
selector to select a CC filter.
36
Locations and Functions of Parts
ND filter
1 Clear
2 1/4ND
2)
3
1/8ND or 1/16ND
2)
4
1/16ND or 1/64ND
5
1/64ND or cross filter
1) Invalid when the HDC1400 is mounted
2) for the HDC1400
m Back tally lamp
This lamp lights red when the red tally signal is supplied to
the camera. When the CALL button on the MSU-900/950
Master Setup Unit or the RCP-700/900-series Remote
Control Panel is pressed, the lamp lights if previously off
or goes off if previously on.
You can display the camera number selected on the menu.
n RET 2 button and selector knob
You may select from among the four return signals (1 to 4)
from the CCU using the selector knob.
By pressing the button, you can view the return video
signal selected by the selector knob, on the viewfinder
screen. Pressing the button again will switch the
viewfinder screen display and monitor output back to the
camera's video signal.
Note
If both the RET 1 and RET 2 buttons are pressed, the RET
1 button takes the priority.
o VF DTL (viewfinder detail adjustment) switch
ON: Emphasizes the contours of the image on the
viewfinder screen. When the switch is set to this
position, you can adjust the amount of detail using the
VF DTL control.
OFF: Disables contour emphasis.
p CALL button
• Press to call the operator of the HDCU1000/1500/3300
Camera Control Unit, the MSU-900/950 Master Setup
Unit, or the RCP-700/900-series Remote Control Panel
connected to the camera. When pressed, the camera's red
tally lamp will light up if previously off, and turn off if
previously on. The CALL button on the connected
control devices will light up, and their buzzer will sound.
• When the CALL button on a connected control device is
pressed, this button will light up.
q VF DTL (viewfinder detail) control
Adjust the amount of detail of the picture on the viewfinder
screen when the VF DTL switch is set to ON. This has no
effect on the output signal of the camera.
CC filter
A Cross filter
B 3200K (clear)
C 4300K
D 6300K
2)
E 8000K