Functional Description - Makita BPT350 Bedienungsanleitung

8. Always remove the battery cartridge before
loading the pin nails, adjustment, inspection,
maintenance or after operation is over.
9. Make sure no one is nearby before operation.
Never attempt to drive pin nails from both the
inside and outside of wall at the same time. pin
nails may rip through and/or fly off, presenting
a grave danger.
10. Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations.
11. Check walls, ceilings, floors, roofing and the
like carefully to avoid possible electrical shock,
gas leakage, explosions, etc. caused by
stapling into live wires, conduits or gas pipes.
12. Use only pin nails specified in this manual.
The use of any other pin nails may cause
malfunction of the tool.
13. Do not tamper with the tool or attempt to use it
for other than driving pin nails.
14. Do not operate the tool without pin nails. It
shortens the service life of the tool.
15. Stop driving operations immediately if you
notice something wrong or out of the ordinary
with the tool.
16. Never drive pin nails into any materials which
may allow the pin nail to puncture and fly
through as a projectile.
17. Never actuate the switch trigger and safety
lever at the same time until you are prepared
to drive pin nails on workpieces. Never defeat
its purpose by securing the safety lever back
or by depressing it by hand.
18. Never tamper with the safety lever. Check the
safety lever frequently for proper operations.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5. Do not short the battery cartridge:
(1)
(2)
(3)
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
2. Never
cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.
4. Charge the Lithium-ion battery cartridge when
you do not use it for more than six months.

FUNCTIONAL DESCRIPTION

ENC007-1
CAUTION:
Always be sure that the tool is switched off and the
•
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
Fig.1
Always switch off the tool before insertion or
•
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
•
the tool while sliding the button on the front of the
cartridge.
To insert the battery cartridge, align the tongue on
•
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can
see the red part on the upper side of the button, it
is not locked completely. Insert it fully until the red
part cannot be seen. If not, it may accidentally fall
out of the tool, causing injury to you or someone
4
Do not touch the terminals with any
conductive material.
Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
recharge a fully charged battery