Ryobi ETS-1825 Bedienungsanleitung Seite 22

ETS-1825 manual 17/06/04
GB
F D E
OPERATION
With the box end of the small spanner, remove the two
■
nuts at the base of the riving knife. Remove the riving
knife/guard assembly. Rearrange the riving knife
between the shims to achieve the correct centering.
WARNING
Properly align riving knife. Improperly aligned
riving knife can cause blade to bind which will
increase risk of kickback.
Adjust the riving knife on the bolts front-to-back as
■
needed to place the riving knife approximately 3-5 mm
(Fig. 11-2) from the blade's outer points. Put the nuts
back on and tighten.
Bring the blade back to the desired angle and height.
■
Lower the blade, insert the throat plate, then securely
tighten the throat plate screws.
TO SET THE SCALE TO THE BLADE
The scale is usable from 0-686 mm to the right side of
the blade and 0-171 mm on the left side of the blade.
The operator can select any desired dimension within
those ranges. Use the following steps to set the scale to
the blade and scale indicator. Begin with the blade at a
zero angle (straight up) (Fig. 12).
Loosen the rip fence by raising the locking handle.
■
Using a framing square, set the rip fence 50mm from
■
the blade tip edge.
Loosen the screw on the scale indicator.
■
Adjust the front rail until the 50mm mark is placed at
■
the scale indicator. Align the rear rail to the front rail.
Tighten the screw and check the dimension and the
■
rip fence.
WARNING
Blades coast after turn off. Possible serious injury
can occur if hands come in contact with blade.
PARALLELING THE BLADE TO THE MITER
GAUGE GROOVE (Fig. 13. 1-3)
Do not loosen any screws for this adjustment until you
have checked with a square and made test cuts to be
sure adjustments are necessary. Once the screws are
loosened. These items must be reset.
WARNING
The blade must be parallel to the miter gauge
slot (40) so the wood does not bind resulting
in kickback. Failure to do so could result in
serious personal injury.
13:04 Page 15
I P NL S DK
English
■
■
■
■
■
■
■
TO USE OUTFEED SUPPORT
The out feed support slides to give the operator
additional support for cutting long work pieces.
■
■
TO USE SLIDING TABLE EXTENSION (1)
■
■
15
N FIN GR H CZ
Lift the blade guard. Raise the blade all the way by
turning the height hand wheel.
Mark beside one of the blade teeth at the front of the
blade. Place the body of a combination square
against the miter gauge groove. Measure the
distance to the right gauge groove.
Turn the blade so the marked tooth is at the back.
Move the combination square to the rear and again
measure the distance to the right miter gauge groove.
If the distances are the same, the blade and the miter
gauge groove are parallel.
If the distances measured are different, loosen the
screws at the back of the table using a 4 mm hex key.
If the back of the blade was too far from the miter gauge
groove, place a block of wood on the left side of the
blade and push it into the blade until the blade is parallel
to the miter gauge groove. Retighten the screws.
If the back of the blade was too close to the miter gauge
groove, place a block of wood on the right side of the
blade and push it into the blade until the blade is parallel
to the miter gauge groove. Retighten the screws.
WARNING
To reduce the risk of injury from kickback, align
the rip fence to the blade following any blade
adjustments. Always make sure the rip fence is
parallel to the blade before beginning any
operation.
With the table saw in the off position, stand behind
the saw.
Grasp the out feed support with both hands and pull
the out feed support until it is fully extended
CAUTION
Work longer than 900 mm may fall from the
saw's table after cut. Such work must be further
supported by suitable means, such as
saw horse, roller stands or another person.
The sliding table extension provides operators
with additional table width for supporting wider
workpieces. Set the rip fence to ......mm.
Loosen the table extension knobs beneath the sliding
table extension by turning them counterclockwise.
RUS RO PL