Residual Risk - Milwaukee M18 FTS210 Originalbetriebsanleitung

Keeping rip fence parallel to the saw blade.
Keep the oor area free of loose material e.g. chips and cut-o s.
In spite of compliance with all relevant design regulations, dangers
may still present themselves when the machine is operated, e.g.:
workpiece parts being thrown o ,
parts of damaged tools being thrown o , noise emissions, wood dust
emissions.
Remove the battery pack before starting any work on the
appliance.
WARNING! To reduce the risk of re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in uid or allow a uid to ow inside them.
Corrosive or conductive uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.
Use only System M18 chargers for charging System M18 battery
packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
WARNING
This device contains a button-type/coin cell lithium battery.
A new or used battery can cause severe internal burns and
lead to death in as little as 2 hours if swallowed or if it enters the
body. Always secure the cover on the battery compartment. If it
does not close securely, stop the device, remove the battery and
keep it out of reach of children. If you believe that someone has
swallowed the battery or that it has otherwise entered the body,
seek immediate medical attention.
SPECIFIED CONDITIONS OF USE
Use this circular saw to cut only wood and wood like products.
Never use the Circular table saw to cut materials other than those
speci ed in the instruction manual.
Stock having a round or irregular cross section (such as rewood)
must not be cut, as it can not be securely held during cutting. When
sawing thin stock layed on edge, a suitable auxilary fence must be
used for rm support.
Rip cutting, cross cutting, mitre cutting and bevel cutting using max.
one mounted saw blade.

RESIDUAL RISK

Even when the product is used as prescribed, it is still impossible
to completely eliminate certain residual risk factors. The following
hazards may arise in use and the operator should pay special atten-
tion to avoid the following:
- Impairment of hearing, restrict exposure and wear appropriate
hearing protection.
- Measures that can be taken by operator to possibly reduce the
e ects of vibration and limit the amount of exposure.
- Health hazards caused by breathing dust developed when sawing
wood, wear a mask if necessary.
MAINTENANCE
Remove the battery pack before starting any adjustment, cleaning
and maintenance work on the device.
Be sure to disconnect the tool from the power supply before atta-
ching or removing the saw blade.
Remove dust regularly. Remove the sawdust which has accummula-
ted inside the saw in order to avoid the risk of re.
Replace the table insert when worn
Clean tool and guarding system with dry cloth.
The ventilation slots of the machine must be kept clear at all times.
Use only Milwaukee accessories and Milwaukee spare parts. Should
components need to be replaced which have not been described,
please contact one of our Milwaukee service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label
and order the drawing at your local service agents or directly at:
Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden,
Germany.
ONE KEY™
To learn more about the ONE-KEY functionality of this device,
please refer to the Quick Start guide included with this product or
go to http://www.milwaukeetool.com/one-key
To download the ONE-KEY app, visit the App Store or Google Play
from your smart device.
We considered the result to be within our minimum acceptable
performance level according to EN 301489-1/ EN 301489-17. And we
will give the operation guidance to the customer in user manual.
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of
the battery pack. Avoid extended exposure to heat or sunshine (risk
of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully char-
ged, after use.Battery packs which have not been used for some
time should be recharged before use.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days: Store the battery
pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% - 50% charged condition ,Every six
months of storage, charge the pack as normal.
Do not dispose of used battery packs in the household refuse or
by burning them. Milwaukee Distributors o er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it o immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
No metal parts must be allowed to enter the battery section of the
charger (short circuit risk).
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit
situations that cause high current draw, the tool will stop for about
2 seconds and then the tool will turn OFF. To reset, release the trig-
ger. Under extreme circumstances, the internal temperatur of the
battery could become to high. If this happens, the battery will shut
down. To reset, release the trigger. Under extreme circumstances,
the internal temperatur of the battery could become to high. If
this happens, the battery will shut down. Place the battery on the
charger to charge and reset it.
GB
English
47