Electric Fryers; Electronic Gas Fryers; Electronic Electric Fryers - kbs 900 Serie Bedienungsanleitung

BURNER IGNITION AND EXTINCTION
Pilot ignition
Press and turn the knob to position "
• Press the knob down fully and light the pilot using the piezo-
electric igniter.
• Hold the knob down for about 20 seconds before releasing it.
If the pilot lame goes out, repeat the operation.
• The pilot lame can be seen by opening the door
• The pilot light can be lit by bringing an open lame up to the
nozzle.
Main burner ignition
• Turn the knob to the chosen temperature setting for cooking.
Switching of
To switch the main burner of, turn the knob to position "
To switch of the pilot lame, press and turn the knob to position
" ".

ELECTRIC FRYERS

The thermostat control knob has the following positions:
0 Of
115-185°C Cooking temperature
Switching on
• Turn the thermostat knob to the chosen temperature setting
for cooking.
• The yellow indicator light switches on.
• The yellow indicator light switches of when the oven reaches
the set temperature.
Switching of
• Turn the thermostat knob to position "0".
• The yellow indicator light switches of.

ELECTRONIC GAS FRYERS

The main switch has the following positions:
O Fryer of
1 Fryer on
The gas valve control knob has the following positions
Burners of
Pilot ignition
Burners on
The electronic thermostat control buttons have the following
positions : Fig.A
START/STOP to switch oil heating on/of
SET , MUTE to set the cooking temperature
MELT melting (melting of solid fat) and maintenance of oil at
100°C
MUTE to stop the acoustic signal
Pilot ignition
• Open the door.
8
Press and turn the knob to position "
• Press the knob down fully and light the pilot using the piezo-
".
• Hold the knob down for about 20 seconds before releasing it.
• The pilot light can be lit by bringing an open lame up to the
Switching on the fryer
To prepare the fryer for use turn the knob to position
• To switch on the fryer turn the main switch to position 1. The
".
• To set melting or maintenance mode press the MELT button
• To start melting or maintenance mode press the START but-
• To suspend melting or maintenance mode press the MELT
Press SET to set the cooking temperature The cooking tempe-
rature appears on the display.Within four seconds press
increase the temperature or
required cooking temperatu-
moments. The temperature of the oil in the well will be display-
ed again.
• To start heating press the START button and keep it pressed
• To suspend heating press the STOP button and keep it
• To switch of the fryer turn the main switch to position 0.
Switching of
To switch the main burner of, turn the knob to position "
To switch of the pilot lame, press and turn the knob to position
"

ELECTRONIC ELECTRIC FRYERS

The main switch has the following positions:
O Fryer of
1 Fryer on
The electronic thermostat control buttons have the following
positions : Fig.A
START/STOP to switch oil heating on/of
electric igniter.
If the pilot lame goes out, repeat the operation.
nozzle.
temperature of the oil in the well is displayed. Important :If the
temperature reading is shown intermittently press STOP and
keep it pressed for at least 2 seconds. If one of the following
messages appears:"E0","E2","EOC", turn of the fryer and
call technical service.
and keep it pressed for at least 2 seconds. The yellow indi-
cator light switches on. In melting mode the appliance heats
intermittently in a manner that is suitable for melting solid fat.
Maintenance mode serves to keep the oil at a temperature
of 100 °C.
ton and keep it pressed for at least two seconds. The green
and yellow indicator lamps will lash.When the maintenance
temperature is reached an audible signal will sound for ive
seconds. The green and yellow indicator lamps remain stea-
dily illuminated.
button and keep it pressed for at least two seconds. The yel-
low indicator light switches of.
for at least two seconds. The green indicator light will lash.
When the preset cooking temperature is reached an audible
signal will sound for ive seconds. The green indicator light
remains steadily illuminated.
pressed for at least two seconds. The green indicator light
switches of.
".
".
.
to decrease it. Once the
re has been set, wait for a few
to
".