Herunterladen Inhalt Inhalt Diese Seite drucken

Renfert hotty LED Bedienungsanleitung Seite 9

Wachstauchgerät
Vorschau ausblenden Andere Handbücher für hotty LED:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4
hotty LED
No. 1457-0000 / No. 1457-1000
ENGLISH
1. Introduction
Thank you for purchasing our hotty
LED wax dipping unit.
Please observe the following notices,
they will help provide you a long and
problem free lifetime of your wax
dipping unit.
2. Application area
The hotty LED is an electronically
regulated wax dipping pot. It is
ideally suited for melting and retai-
ning any conventional dipping wax.
The hotty LED shows its quality in
use when it comes to the following
points:
The precise temperature control
(+/- 2°C [3.6°F]) provides you with a
very constant quality of copings.
Together with the heating unit, which
reacts to the environmental tempera-
ture, this excludes the possibility of
over heating and consequent
damage to the dipping wax.
Please be aware that the initial
heating process is very gentle to the
dipping wax and it may take some
time before the wax if fully melted.
Thanks to a slow continual increase
of the working temperature, there is
no chance that the temperature inside
the pot will exceed the set point.
The hotty LED offers you optimal
working conditions. The housing is
designed to let both left and right-
handed people rest their hand on the
working table whilst dipping. In addi-
tion, the lid of the wax-dipping unit
can be moved completely out of the
working area.
2.1 Environmental conditions
(In accordance with IEC 60664-1)
The hotty LED must only be operated:
• in closed rooms
• below an altitude of 2,000 m
[6,500 ft] above mean sea level
• under environment temperature
between 5 – 40°C [41-104°F]
• at a maximum relative humidity of
80% at 31°C [87,8°F], linear
declination to 50% at 40°C [104°F]
• when the mains supply do not
fluctuate more than 10% of the
Norm.
• at pollution level 2
• with over voltage category II.
3. Safety Information
• Before initial use, check the
voltage recommendations
on the name plate (rear side
of the unit) and compare
with the mains supply.
• Units with damaged power
cables or other defects are
not to be used.
• Mains supply cable (G) must
be unrolled when in use
(danger of over heating in
the event of short circuit).
• Do not cover the transfor-
mer when in use.
• The power cables are not to
be shortened in any event.
• Incorrect use of the socket
fittings can cause short-
circuiting.
hotty LED
No. 1457-0000 / No. 1457-1000
ENGLISH
1. Introduction
Thank you for purchasing our hotty
LED wax dipping unit.
Please observe the following notices,
they will help provide you a long and
problem free lifetime of your wax
dipping unit.
2. Application area
The hotty LED is an electronically
regulated wax dipping pot. It is
ideally suited for melting and retai-
ning any conventional dipping wax.
The hotty LED shows its quality in
use when it comes to the following
points:
The precise temperature control
(+/- 2°C [3.6°F]) provides you with a
very constant quality of copings.
Together with the heating unit, which
reacts to the environmental tempera-
ture, this excludes the possibility of
over heating and consequent
damage to the dipping wax.
Please be aware that the initial
heating process is very gentle to the
dipping wax and it may take some
time before the wax if fully melted.
Thanks to a slow continual increase
of the working temperature, there is
no chance that the temperature inside
the pot will exceed the set point.
The hotty LED offers you optimal
working conditions. The housing is
designed to let both left and right-
handed people rest their hand on the
working table whilst dipping. In addi-
tion, the lid of the wax-dipping unit
can be moved completely out of the
working area.
2.1 Environmental conditions
(In accordance with IEC 60664-1)
The hotty LED must only be operated:
• in closed rooms
• below an altitude of 2,000 m
[6,500 ft] above mean sea level
• under environment temperature
between 5 – 40°C [41-104°F]
• at a maximum relative humidity of
80% at 31°C [87,8°F], linear
declination to 50% at 40°C [104°F]
• when the mains supply do not
fluctuate more than 10% of the
Norm.
• at pollution level 2
• with over voltage category II.
3. Safety Information
• Before initial use, check the
voltage recommendations
on the name plate (rear side
of the unit) and compare
with the mains supply.
• Units with damaged power
cables or other defects are
not to be used.
• Mains supply cable (G) must
be unrolled when in use
(danger of over heating in
the event of short circuit).
• Do not cover the transfor-
mer when in use.
• The power cables are not to
be shortened in any event.
• Incorrect use of the socket
fittings can cause short-
circuiting.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis