Herunterladen Inhalt Inhalt Diese Seite drucken

GYS EXAFEED 4L Bedienungsanleitung Seite 17

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 24
7-
Man to Machine Interface
8-
EURO connector
CONTROL BOARD (MMI) (FIG-2)
1-
Voltage display
2-
Wire speed / current display
3-
Amperes indicator
4-
m /mn indicator
5-
Overheat indicator
6-
Disruption of normal operations indicator
7-
Voltage adjustment knob:
8-
Wire speed / inductance adjustment knob
9-
Inductance selection button
10-
Wire speed indicator
POWER SUPPLY – STARTING UP
The EXAFEED 4L wire feeder has been solely designed to operate with the EXAGON 400 CC/CV welding machine (ref. 010925).
The connection between these two elements is done via one of the following connection cables :
Cooling
Length
5m
10m
Air
15m
20m
5m
10m
Liquid
15m
20m
CONNECTIONS AND RECOMMENDATIONS
The connection between the welding machine and the wire feeder must be done while the power supply is off.
Connection cable on the wire feeder :
- Open the connection cable's access panel (FIG 1 - n°2)
- Pass the cable through the opening at the back of the wire feeder
- Lock the connection cable on the wire feeder by twisting it clockwise by 1/4 then lock the support using the screw supplied with the connection cable.
- Perform the connection.
Connection cable on welding machine :
- Connect the earth clamp on the positive (+) or negative (-) terminal depending on the wire type.
- Connect the connection cable on the remaining terminal for power.
- Connect the command connector on the 10 pin DIN connector located between the welding machine's power connectors.
WIRE REEL INSTALLATION (FIG-4)
• Remove the torch shroud (FIG-4, F) and contact tip (FIG-4, E). Open the door of the machine.
FIG-4, A :
• Place the reel on the driving pin of the reel support. For a 200 mm (10kg) wire reel, tighten the wire reel support to the maximum.
• Set the brake (FIG-4, 2) to prevent wire entanglement when the weld stops. In general, do not excessively tighten the brake, which would cause
the motor to overheat.
FIG-4, B :
• Set the rollers that fit the intended use of the machine. The supplied rollers are double groove rollers (Ø1/ and Ø1.2). The indication on the visible
side of the roller is the diameter in use. For a Ø1.2 mm wire, use the Ø1.2 groove. For aluminium welding, use suitable rollers (U groove).
FIG-4, C :
To change the wire, proceed as follows :
• Untighten the wheels (FIG-4, 4) at the maximum and lower them, insert the wire, then close the wire feed motor and tighten the wheels according
to the instructions.
• Start the motor by pressing the torch trigger (FIG 1 - n°5)
• Make the wire come out of the torch by 5 cm, then put a suitable contact tip at the end of the torch (FIG-4, E), as well as the shroud (FIG-4, F).
Remarks :
• A torch liner that is too narrow may cause wire feeding problems as well as motor overheating.
• The torch connector must also be securely tightened to prevent overheating.
• Check that neither the MIG/MAG wire nor the wire reel are in contact with the machine's mechanical parts, otherwise there si a
danger of short-circuit.
EXAFEED 4L
Section
Reference
70mm²
047587
70mm²
047594
95mm²
047600
038349
95mm²
038431
70mm²
047617
70mm²
047624
95mm²
047631
038448
95mm²
038455
15-
Water connector
16-
Water connector
11-
Inductance mode indicator
12-
Active remote control indicator
13-
Locked keypad indicator
14-
Locked keypad button
15-
Remote control selection button / remote control activation
16-
2T indicator
17-
4T indicator
18-
Spot/Delay indicator
19-
Gas purge
20-
Wire inching
EN
17

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis