Messner system-X 750 Bedienungsanleitung Seite 5

GB
Please read these instructions thoroughly before using the pump!
Use: Centrifugal pump for submersible usage with resin encapsulated
motor.
The pump is suitable for use in water, e.g. for garden ponds, fountains,
terraced fountains, indoor fountains, in fi shponds, for the operation of
fi lter systems, fl owing brooks etc. as well as for circulating and oxygena-
ting water.
The pump may not be used in or on the side of swimming pools!
For all technical data please refer to the type plate.
Safety measures
- Caution! It may only be used in garden ponds and in their protection
area if the electrical installations have been set up to comply with the
code's requirements. Please contact an electrician.
- Before use: Check whether mains connection and plug are intact.
- Mains voltage and type of current have to correspond to the data on the
type plate.
- The pump has to be connected to a regular safety plug socket
through a residual current device (RCD, 30 mA).
- The connection box should be located in a water-protected area. It
should be at least 2 m away from the edge of the pond (see fi g.1).
- Keep the plug dry!
- Pull out mains plug before starting to work on the pump, fountain
or pond. It is not allowed to run the pump when people are inside
the water (disconnect the pump)!
- Important! If the mains connection or the motor housing is damaged,
the pump cannot be used anymore. It cannot be repaired since the
connection is cast into the motor housing.
- Never hang up or transport the pump by the cable!
- Operate the pump only when it is immersed in water!
Start-up (see fi g.1)
Important! Do not let the pump run dry. This could cause damage to
the appliance.
- Immerse the pump completely in your pond. This causes the pump body
to be fi lled with water.
- A water level of approx. 12 cm is required for submersible use in order to
prevent the pump from taking-in air.
- The water temperature should not exceed 35°C.
- Do not let the pump freeze in the wintertime.
- The pump is switched on by putting the plug in the socket.
- To prevent the pump becoming unnecessarily dirty, place it above the
mud in your pond, in a fi rm and horizontal position (on a brick)!
- A range of accessories may be fi tted onto the threaded connection of
the pump.
- Running in conjunction with fountain jets, the pump should be
positioned fi rmly and horizontally (on a brick).
6
Dismantling / Assembly (see fi g. 2 - 4)
1. Follow the safety measures. Disconnect the pump!
2. Push in the two brackets on the front of the pump, push the top
shell (1) up and remove it.
3. Lift the entire pump (8) out of the bottom shell (2).
4. Turn the lid (4) counterclockwise through approx. 20° in the oppposite
direction to the stop.
5. Remove the lid (4) from the pump (8).
6. Remove the complete rotor (5) from the pump (8).
The shaft of the rotor (5) is mounted on two rubber bearings in the
pump (8) and in the lid (4).
7. The complete rotor (5) can be made to rotate on the shaft.
8. Clean all parts using clear water so that they may be moved very
easily.
Do avoid using any sharp instruments.
9. Re-assemble the pump as follows:
9.1. Replace complete rotor (5) in the pump (8).
Make sure the rubber bearings are seated correctly in the pump (8)
and the lid (4).
9.2. Fit turned lid (4) onto the pump (8) and turn it clockwise until stop.
9.3. Place the pump (8) into the bottom shell (2).
9.4. Rest the top shell (1) against the two rear hooks on the bottom
shell (2) and snap it into the front brackets.
To ensure proper functioning, repeat the above procedure frequently,
depending on clogging and working time.
Maintenance
In order to prolong the service life of your pump and to keep it in good
operating condition, it is recommended to carry out maintenance and
cleanup regularly. This can be done by everyone, quickly and easily.
See "Dismantling / Assembly"
Servicing intervals:
- Initially, clean your pump daily and make sure it functions properly.
Clean the fi lter housing if necessary.
- Since servicing intervals (complete cleanup) will vary depending on
pond pollution, repeat the periodic service to your pump in accordance
with the requirements given.
Should you determine that there are damaged or worn parts, do replace
them. See "Spare parts"
Winter / Pump care
Protect your pump from freezing!
Take the pump out of your pond in autumn.
Clean the pump completely following the outlined instructions.
Store the tank in a frost-resistant room.
Spare parts
For ordering spare parts, please indicate the pump type, the designation
and the Art.-No. as per table below (see also fi g. 2 - 4).
Item Designation Pump Type
1 Upper shell system-X 750, system-X 1000
2 Lower shell system-X 750, system-X 1000
3 Handle system-X 750, system-X 1000
4 Rotor system-X 750
system-X 1000
5 Inlet cover system-X 750, system-X 1000
6 Distanz C0 system-X 750, system-X 1000
7 Accessories system-X 750, system-X 1000
7
Art-No.
104/003661
104/003662
104/003663
168/009071
168/009092
168/009150
104/003834
104/003957