Herunterladen Inhalt Inhalt Diese Seite drucken

Specifications - Makita AN610H Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für AN610H:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 33
ENGLISH (Original instructions)
4-1. Adjuster
4-2. Shallow
4-3. Deep
5-1. Too deep
5-2. Flush
5-3. Too shallow
6-1. Hook
7-1. Hole
7-2. Protrusion
7-3. Nose adapter
8-1. Magazine cap
8-2. Latch lever
8-3. Door
9-1. Adjustfit
9-2. Change plate

SPECIFICATIONS

Min. hose diameter
Dimensions (L X H X W)
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Wear safety glasses.
Do not use on scaffoldings, ladders.
Intended use
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2 "x 4" housing.
Noise
The typical A-weighted noise level determined according
to EN792:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
Explanation of general view
9-3. Arrow
10-1. Door
10-2. Nail guide
10-3. Feeder
11-1. Trigger
11-2. Contact element
12-1. Trigger
12-2. Contact element
13-1. Change lever
13-2. Trigger
14-1. Change lever
14-2. Trigger
15-1. 0.7 mm or less thick for steel plate
15-2. Thickness of workpiece
15-3. 10 mm or more
Model
Air pressure
Nail length
Nail capacity
Net weight
) : 86 dB(A)
pA
) : 99 dB(A)
WA
Sheet-collated coil nail 32 mm - 65 mm
Wire-collated coil nail 250 pcs,300 pcs,400 pcs
END106-2
Vibration
The vibration emission value determined according to
EN792 :
Vibration emission (a
Uncertainty (K) : 1.5 m/s
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
ENE059-1
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
ENG102-3
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
4
15-4. C-shaped steel (Thickness 1.6
mm - 2.3 mm)
16-1. Nail driven to a proper depth
16-2. Nail driven too deep will cause
deformation of workpieces
17-1. Nail length
17-2. Wood thickness
17-3. Concrete range 10-15 mm
19-1. Small rod
20-1. Screwdriver
21-1. Cap
22-1. Drain cock
23-1. Air filter
24-1. Oiler
24-2. Pneumatic oil
AN610H
0.98 - 2.26 MPa (9.8 - 22.6 bar)
Wire-collated coil nail 32 mm - 65mm
Sheet-collated coil nail 200 pcs
5.0 mm
282 mm X 277 mm X 136 mm
1.9 kg
) : 3.0 m/s
h
2
ENG233-2
2
ENG901-1

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

An620h

Inhaltsverzeichnis