EdilKamin BIJOUX Installations-, Betriebs- Und Wartungsanleitung Seite 48

Shutdown
While the boiler-stove is working pressing the 0/1 key for 2
seconds begins the shutdown process and "STOPPING" is
displayed (for 10 minutes). The turning off phase includes:
- The interruption of falling pellets
- The circulation of running water.
- Smoke extractor operating at maximum speed.
- Air ventilation
Never pull the plug during shutdown.
N.B. Please note that the circulator runs until the water tempe-
rature drops below 40° C.
Setting the clock
Press the MENU button for 2 seconds and use the + and – keys
to follow the instructions given on the display to access the
'Clock' menu. This allows you to set the time on the electronic
control board. Then press MENU and the following data appe-
ars in sequence – this can be adjusted: day, month, year, hour,
minutes, day of the week. When 'Save?' appears on the display,
you can check that the settings have been entered correctly
before con rming. Press MENU to save the information ('Save
OK' then appears on the display).
Programmer to ignite and shutdown the thermal stove at
various times during the week.
Press the MENU button on the remote control or the synoptic
panel for 2 seconds to access the time setting function and
press the + key to access the weekly timer function 'Program
ON/OFF' will appear on the display. The timer allows you to
set a number of ignitions and shutdowns per day (up to a ma-
ximum of three), for each day of the week. As you con rm via
the MENU button, one of the following options will appear:
- No Prog. (no program is set)
- Program/daily (a single program is set for every day)
- Program/weekly (a program is set for each day of the week)
Move from one to the other using the + and – keys.
Use the MENU button to con rm the 'Daily program'option
and access the selection of the number of programs (ignition/
shutdown) to be set per day. Use the 'Program/daily' option to
set the identical program/s for every day of the week.
The following will be displayed if the + key is pressed:
- No Prog.
- Prog. No. 1 (one ignition and one shutdown per day), Prog.
No. 2 (same as before), Prog. No. 3 (same as before)
Use the button to show them in reverse order. If the 1st pro-
gram is selected, the ignition time is shown.
The display shows: 1 Ignition Hour 10.30; use the +/– keys to
change the hour and press MENU to con rm.
The display shows: 1 Ignition Minutes 10.30; use the +/– keys
to change the minutes and press MENU to con rm.
In the same way, adjust the shutdown times.
The program is con rmed by pressing the MENU button when
"Saved" appears on the display.
When con rming 'Program/week', you will need to choose the
day to which the program is to apply:
1 Mon; 2 Tues; 3 Wed; 4 Thurs; 5 Fri; 6 Sat; 7 Sun
INSTRUCTIONS FOR USE
- 48
Once you have chosen the day by scrolling through them with
the + and – keys, con rm by pressing MENU and proceed with
the settings of the programs in the same way as for the 'Pro-
gram/daily', selecting whether or not to enable a program for
each day of the week and choosing the number and times of
interventions.
Should you make a mistake whilst setting the programs you
can exit without saving by pressing the 0/1 key and 'Saved'
will appear on the display. Should the hopper run out of pellets,
the boiler-stove will block and 'Stop/Flame' will appear.
Pellet reserve warning
The boiler-stove is equipped with an electronic pellet detection
system.
The pellet detection system is integrated into the electronic
control board, allowing the stove to monitor how many kilos of
pellets are left.
This veri cation is implemented at any point whilst the stove is
in operation mode.
For correct system operation, it is important that the following
procedure is adhered with during the rst ignition (that must
be implemented by the DEALER). Before starting to use the
pellet detection system, you must load and consume a full sack
of pellets.
This allows for a brief running-in of the loading system.
Subsequently load 15 kg of pellets.
Then press the 'reserve' button once, thereby storing the data
into the memory that 15 kg have been loaded.
From now on the display will show the remaining pellets as
they decrease in kg (15...14...13). Each time pellets are reloa-
ded you must
enter the quantity. E.g. when loading 15 kg, simply press the
'pellet load' button to enter this into the memory.
For other quantities, or in the event of an error, you can specify
the quantity using the pellet reserve menu as follows:
Press the MENU button for 2 seconds to view the SETTINGS.
Press + or – consecutively to view T. Max exit.
Con rm by pressing MENU and the remaining quantity of
pellets will be displayed + that being loaded (default is 15 and
can be changed using the +/- keys).
Press the + button to increase the kg value to be entered, press
the -button to reduce the value, repeatedly press the -button to
get 00kg load (R on the display), which allows deletion of the
residual load.
Should the hopper run out of pellets, the boiler-stove will block
and 'Stop/Flame' will appear.
Variation feeding pellets (ONLY AFTER SUGGESTED BY
DEALER)
Press and hold the "M" key on the remote control for two se-
conds. Scroll through the display instructions using the "+"
and "–" keys, to the description "ADJ-PELLET". By con-
rming this function using the menu key you can adjust the
supply of pellets,
by reducing the set value, you decrease the supply of pellets,
increasing the set value increases the supply of pellets. This
function can be useful in the event that one changes the type of
pellets used, no longer using those for which the boiler-stove
was calibrated, thus necessitating an adjustment of the load
setting.
-