Proper Use; Residual Risks; Electrical Connection - Scheppach TIGER 2000S Originalanleitung

Stability
• Make sure the machine is installed on a firm ground
with sufficient stability.
• Make sure the workplace is sufficiently illuminated.
Mains Connection of the Machine
• Check the mains connecting lines. Do not use de-
fective lines. See electrical connection.
• Pay attention to the direction of rotation of the mo-
tor and the tools. See electrical connection.
• Installations, repair, and maintenance work relating
to the electric installation may only be performed
by specialists.
• Turn off the machine before you repair failures. Dis-
connect the mains plug.
• Turn off the motor when you leave the workplace.
Disconnect the mains plug.
• Disconnect the machine from any external energy
supply also in case of only moving the machine to
another, nearby location! Properly reconnect the
machine to the mains before you turn it on again!
Setup and Adjustment of the Machine
• Only perform retooling, measuring, and cleaning
work when the motor is turned off. Disconnect the
mains plug, and wait until the rotating tool stands
still.
• All protection and safety devices must be immedi-
ately reinstalled once the repair and maintenance
work is completed.
m Proper Use
• The grinding machine has been exclusively de-
signed for grinding steel using the offered tool
(no hard alloy).
• The machine meets the currently valid EU machine
directive.
• The machine has been designed for a one-shift
operation, operating factor S1 100%.
• Observe all safety instructions and warnings on the
device.
• Make sure that all safety instructions and warnings
on the machine always are in a readable state.
• Only use the machine if it is in a technically fault-
less state. Pay attention to the intended use, the
safety and dangers and comply with the operating
instructions! Immediately repair (or have repair)
failures which may affect the safety.
• The safety, working, and maintenance instructions
and the dimensions set forth in the specifications
must be observed.
• The applicable regulations for the prevention of
accidents and other, generally recognized safety
rules must be observed.
• The machine may only be used, maintained or re-
paired by trained persons who are familiar with the
machine and have been informed about the dan-
gers. Unauthorized modifications of the machine
exclude a liability of the manufacturer for damages
resulting from the modifications.
• The machine may only be used with original acces-
sories and original tools of the manufacturer.
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• Any other use is considered to be not intended. The
manufacturer excludes any liability for resulting
damages, the risk is exclusively borne by the user.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
Warning! This electric tool generates an electromag-
netic field during operation. This field can impair ac-
tive or passive medical implants under certain condi-
tions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical
implants consult with their physician and the manu-
facturer of the medical implant prior to operating the
electric tool.
m Residual Risks
The machine has been constructed according to the
state of the art and the recognized safety rules. Nev-
ertheless, single residual risks may occur during the
operation.
• The rotating grinding wheel may cause injuries of
fingers and hands.
• Danger caused by electric current if inappropriate
electrical connecting lines are used.
• Furthermore, non obvious residual risks may exist
in spite of all measures taken.
• Residual risks can be minimized by carefully ob-
serving the safety instructions and the intended
use as well as the entire operating instructions.
Assembly
Assemble the stone and the tool table and hang the
water tank as in Figure 1 on the machine.
Installation and Adjustment
Please make sure that your grinding machine is in-
stalled in an upright and stable manner on a firm
ground with sufficient illumination.
The machine has no front or rear side. You can alter-
natively grind with or against the direction of rotation.
m Electrical Connection
The installed electric motor is connected and is ready
to work.
The connection complies with the relevant VDE and
DIN regulations.
The connection to the mains supply on the cus-
tomer side and the used extension line must
meet these regulations or the provisions of the
local power supply company.
Defective Electric Connection Lines
Often, insulation damages occur on electrical con-
nection lines.
11 | GB