Setting Into Operation; Power Supply - IMG STAGELINE PARL-102DMX Bedienungsanleitung

damage will be accepted if the units are used for
other purposes than originally intended, if they
are not safely mounted, not correctly connected
or operated, or if they are not repaired in an
expert way.
G
Important for U. K. Customers!
The wires in this mains lead are coloured in
accordance with the following code:
green/yellow = earth
blue = neutral
brown = live
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:
1. The wire which is coloured green and yellow
must be connected to the terminal in the plug
which is marked with the letter E or by the earth
symbol , or coloured green or green and yel-
low.
2. The wire which is coloured blue must be con-
nected to the terminal which is marked with the
letter N or coloured black.
3. The wire which is coloured brown must be con-
nected to the terminal which is marked with the
letter L or coloured red.
Warning – This appliance must be earthed.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which is not harmful to
the environment.
3 Applications
This flat LED spotlight serves for illumination e. g.
on stage, in discotheques and festival rooms. As a
light source, 36 extra bright LEDs of 1 W each are
used which have a low power consumption, a low
heat development and a long life. The LEDs allow
to radiate coloured light in the three primary colours
(red, green and blue) and light which can be mixed
from the primary colours by addition. Besides,
colour crossfadings and stroboscopic effects are
possible.
The spotlight can be operated via the remote
control FS-2PARL available as an accessory or via
a DMX light controller (4 DMX control channels).
However, it can also be operated without a con-
troller, either on its own or interconnected with sev-
eral PARL-102DMX units in the master/slave
mode. The integrated microphone provides effects
in sync with the music.

4 Setting into Operation

4.1 Mounting
G
Always place the unit so that a sufficient air cir-
culation is ensured during operation. The air
vents at the housing must not be covered in any
case.
G
The distance to the illuminated object should be
50 cm as a minimum.
WARNING The spotlight must be mounted in a
safe and expert way. If it is installed
at a place where people may walk or
sit under it, it must additionally be
secured, e. g. by a safety rope. Lead
the safety rope through the lug (11)
and fix it so that the maximum falling
distance of the unit would not exceed
20 cm.
1. Fix the spotlight via the mounting brackets (1),
e. g. with a stable mounting screw or a support
for lighting units (C hook) to a cross bar.
To align the spotlight, release the two locking
screws (7) at the mounting brackets. Adjust the
desired inclination of the spotlight and retighten
the screws.
2. As an alternative, the spotlight can also be set
up as desired. For this purpose spread the
mounting brackets below the spotlight so that
they serve as a support. Then tighten the locking
screws.

4.2 Power supply

Connect the supplied mains cable to the mains jack
(10) first and then to a socket (230 V~/ 50 Hz). Then
the unit is ready for operation and can be operated
via a DMX light controller (
independently through the control programme
adjusted ( chapter 5.1). To switch off, disconnect
the mains plug from the socket.
WARNING Never look directly into the light
source for a longer time; this may
cause eye damage.
Please note that fast changes in
lighting, e. g. flashing light, may trig-
ger epileptic seizures with photosen-
sitive persons or persons with epi -
lepsy!
If several PARL-102DMX units are used, the jack
POWER LINK OUTPUT (9) of the first unit can be
chapter 5.4) or it runs
GB
11