Flex MS 1706 FR Originalbetriebsanleitung Seite 21

Wall chaser MS 1706 FR
Changing the cutting discs/
changing the groove width
`^rqflk>
oáëâ=çÑ=áåàìêó>=tÉ~ê=éêçíÉÅíáîÉ=ÖäçîÉëK
1. Pull out the mains plug.
2. Lift the lock (5) for the guard hood and
rotate by 180°.
3. Remove the guard hood (3).
4. Press the spindle lock (12) and loosen the
quick-release clamping nut.
t^okfkd>=
oáëâ=çÑ=áåàìêó=~åÇ=Ç~ã~ÖÉK
qÜÉ=ÇáêÉÅíáçå=çÑ=êçí~íáçå=áåÇáÅ~íÉÇ=çå=íÜÉ=
ÅìííáåÖ=ÇáëÅ=ãìëí=~ÖêÉÉ=ïáíÜ=íÜÉ=ÇáêÉÅíáçåJçÑJ
êçí~íáçå=~êêçï=çå=íÜÉ=ÖÉ~êÄçñ=ENPFK
klqb
qÜÉ=êçìÖÜ=ëáÇÉ=çÑ=íÜÉ=èìáÅâJêÉäÉ~ëÉ=Åä~ãéáåÖ=åìí=
~äï~óë=Ñ~ÅÉë=íÜÉ=ÅìííáåÖ=ÇáëÅ=çê=Çáëí~åÅÉ=ï~ëÜÉêK
5. Remove the cutting discs (b), clamping
flange (d) and distance washers (c).
To change the cutting discs:
 Attach new cutting discs (b), distance
washers (c) and clamping flange (d)
in reverse sequence.
 Screw on the quick-release clamping nut
(a). Depress the spindle lock (12) and
manually tighten the quick-release
clamping nut (a).
To change the groove width:
The groove width can be set by rearranging
the distance washers.
klqb
qÜÉ=ãáåáãìã=ÖêççîÉ=ïáÇíÜ=áë=NM ããK=
få íÜáë Å~ëÉ=çåäó=íÜÉ=Åä~ãéáåÖ=Ñä~åÖÉ=áë=ÑáííÉÇ=
ÄÉíïÉÉå=íÜÉ=ÅìííáåÖ=ÇáëÅëK=få ~ää Çáëí~åÅÉ=
ï~ëÜÉêë=EÅF=~êÉ=ÑáííÉÇ=áå=Ñêçåí=çÑ íÜÉ=èìáÅâJ
êÉäÉ~ëÉ=Åä~ãéáåÖ=åìí=E~FK
 Attach the cutting disc (b), distance
washers (c) according to the required
groove width and clamping flange (d).
 Attach the remaining distance washers (c).
21