Functional Description - Makita GA5020 Bedienungsanleitung

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and
•
unplugged before adjusting or checking function
on the tool.
Shaft lock
Fig.1
CAUTION:
Never actuate the shaft lock when the spindle is
•
moving. The tool may be damaged.
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
Switch action
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and
returns to the "OFF" position when released.
For tool with type A switch trigger (For Models
GA5020, GA5020C, GA6020, GA6020C)
Fig.2
For tool without lock button and lock-off button
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For tool with lock button
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and
then push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
For tool with lock-off button
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
For tool with type B switch trigger (For Models
GA5021, GA5021C, GA6021, GA6021C)
Fig.3
For tool with the lock-on switch
To start the tool, simply pull the switch trigger (A).
Release the switch trigger to stop. For continuous
operation, pull the switch trigger (A) and then push in
the lock lever (B). To stop the tool from the locked
position, pull the switch trigger (A) fully, then release it.
For tool with the lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided. To start the tool, push in the lock
lever (B) and then pull the switch trigger (A). Release
the switch trigger to stop.
For tool with the lock on and lock-off switch
To prevent the switch trigger from accidentally pulled, a
lock lever is provided. To start the tool, push in the lock
lever (B) and then pull the switch trigger (A). Release
the switch trigger to stop. For continuous operation,
push in the lock lever (B), pull the switch trigger and
then push the lock lever further in (B). To stop the tool
from the locked position, pull the switch trigger (A) fully,
then release it.
Electronic function
Constant speed control (For models
GA5020C,GA5021C,GA6020C,GA6021C)
Possible to get fine finish, because the rotating
•
speed is kept constantly even under the loaded
condition.
Additionally, when the load on the tool exceeds
•
admissible levels, power to the motor is reduced to
protect the motor from overheating. When the load
returns to admissible levels, the tool will operate
as normal.
Soft start feature
Soft start because of suppressed starting shock.
•
Indication lamp
Fig.4
The indication lamp lights up green when the tool is
plugged. If the indication lamp does not light up, the
mains cord or the controller may be defective. The
indication lamp is lit but the tool does not start even if
the tool is switched on, the carbon brushes may be
worn out, or the controller, the motor or the ON/OFF
switch may be defective.
Unintentional restart proof
Even locking lever keeping the switch trigger depressed
(Lock-on position) does not allow the tool to restart even
when the tool is plugged.
At this time, the indication lamp flickers red and shows
the unintentional restart proof device is on function.
To cancel the unintentional restart proof, pull the switch
trigger fully, then release it.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the
tool.
Installing side grip (handle)
CAUTION:
Always be sure that the side grip is installed
•
securely before operation.
Fig.5
Screw the side grip securely on the position of the tool
as shown in the figure.
9