Ryobi RBL42BP Bedienungsanleitung Seite 16
Vorschau ausblenden
Andere Handbücher für RBL42BP:
- Bedienungsanleitung (316 Seiten) ,
- Bedienungsanleitung (313 Seiten)
Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
FR
EN DE
ES
IT
EN
FR
DE
ES
IT
DE
FR
EN
ES
IT
ES
FR
EN
DE
IT
IT
FR
EN
DE
ES
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICING DEALER.
FR
EN
DE
ES
IT
PROBLEM
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
Engine will not start.
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
FR
EN
DE
ES
IT
PT
Engine starts but will not accelerate.
FR
EN
DE
ES
IT
PT
Engine starts but will only run at
FR
EN
DE
ES
IT
PT
high speed at half choke.
Engine does not reach full speed
and emits excessive smoke.
Engine starts, runs, and accelerates
but will not idle.
PT
NL
SV
DA NO
PT
NL
SV
DA NO
PT
NL
SV
DA NO
English (Original instructions)
PT
NL
SV
DA NO
TROUBLESHOOTING
PT
NL
SV
DA NO
PT
NL
SV
DA NO
POSSIBLE CAUSE
NL
SV
DA NO
No spark.
SV
NL
DA NO
DA
NL
SV
NO
No fuel.
NO
NL
SV
DA
FI
NL
SV
DA NO
NL
SV
DA NO
FI
NL
SV
DA NO
FI
NL
SV
DA NO
FI
NL
SV
DA NO
FI
Engine is flooded.
NL
SV
DA NO
FI
NL
SV
DA NO
FI
NL
SV
DA NO
FI
NL
SV
DA NO
FI
Starter rope now harder to pull
NL
SV
DA NO
FI
than when new.
NL
SV
DA NO
FI
Engine requires approximately
three minutes to warm up.
NL
SV
DA NO
FI
NL
SV
DA NO
FI
Carburetor requires adjustment.
Check lubricant fuel mixture.
Air filter is dirty.
Spark arrestor screen is dirty.
Idle speed screw on carburetor
requires adjustment.
FI
HU CS RU
RO PL
FI
HU CS RU
RO PL
FI
HU CS RU
RO PL
FI
HU CS RU
RO PL
FI
HU CS RU
RO PL
FI
HU CS RU
RO PL
SOLUTION
FI
HU CS RU
RO PL
The spark plug may be damaged, remove it and
check for dirt and cracks. Replace with a new
FI
HU CS RU
RO PL
spark plug.
Push primer bulb until bulb is full of fuel. If bulb
FI
HU CS RU
RO PL
does not fill, primary fuel delivery system is
blocked. Contact a servicing dealer. If primer bulb
FI
HU CS RU
RO PL
fills, engine may be flooded, proceed to next item.
HU CS RU
RO PL
● Remove spark plug, then turn the unit so the
spark plug hole is aimed at the ground.
HU
CS RU
RO PL
● Set the choke lever to "Run" position and pull
starter cord 10-15 times. This will clear excessive
CS
HU
RU
RO PL
fuel from the engine.
● Remove any fuel from the product.
RU
HU CS
RO PL
● Clean and reinstall the spark plug.
RO
● Clean up any spilled fuel and move at least 9m
HU CS
RU
PL
away before restarting.
PL
● Pull starter handle 3 times with the choke lever
HU CS
RU RO
at "Run" position.
HU CS
RU RO
PL
● If the engine does not start, set the choke lever
to "Full" choke position and repeat the normal
HU CS
RU RO
starting procedure.
PL
● If the engine still fails to start, repeat procedure
HU CS
RU RO
PL
with a new spark plug.
HU CS
RU RO
PL
Contact a servicing dealer.
HU CS
RU RO
PL
Allow engine to completely warm up. If engine
does not accelerate after three minutes, contact a
HU CS
RU RO
PL
servicing dealer.
HU CS
RU RO
PL
Contact a servicing dealer.
Use fresh fuel and the correct 2-stroke lubricant
mix.
Clean air filter. Refer to Cleaning the Air Filter
Screen earlier in this manual.
Contact a servicing dealer.
Turn idle speed screw clockwise to increase idle
speed.
15
SL
HR ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
HR
SL
ET
LT
LV
ET
SL
HR
LT
LV
LT
SL
HR
ET
LV
LV
SL
HR
ET
LT
SK
SL
HR
ET
LT
LV
SL
HR
ET
LT
LV
SK
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
SK BG
BG
BG
Werbung
Inhaltsverzeichnis
