Environmental Protection - Crown CT13394 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für CT13394:

Seite von 156

/ 156
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

smoothness to be obtained� The best method to select

sanding sheet, is to practically test for best results�

Sanding

Prior to commencement of work one

should perform test sanding on an un-

necessary element (made of the same

material or with the same coating as the

machined component) to ensure that the coarse-

ness and type of sanding sheet 9, as well as the

oscillation frequency of the sanding plate 8 have

been selected properly.

• Ensure that the element to be sanded is firmly se-

cured�

• Turn on the power tool earlier, before sanding

plate 8 touches the element to be sanded and allow

the engine of the power tool to reach maximum oscil-

lation rate�

• Apply sanding plate 8 to the surface of the machined

element and move the power tool in circular or recip-

rocating motion�

• Perform sanding with the whole surface of sanding

plate 8�

• Do not press the power tool excessively, since this

will not provide better results, but will only overload the

engine of the power tool and will result in higher sand-

ing sheet 9 consumption�

• Do not stop the power tool in a single spot this will

result in a depression in the stoppage place�

• At relevant time, replace the used or dust-blocked

sanding sheets 9�

• Use sanding sheets 9 of varying coarseness com-

mence the work with a coarse sheet and gradually pro-

ceed to finer sheets. It will make the work faster and

will result in smoother surface�

• Do not reuse sanding sheets 9 that were previously

used for sanding metal for any other materials�

Polishing

[CT13395]

During polishing, it is recommended

to set lower oscillation frequency of

sanding plate 8 - this will prevent the

overheating of machined surface. Prior

to commencement of work, perform test polishing

to ensure whether the polishing agent and oscil-

lation frequency of sanding plate 8 have been se-

lected properly.

• Apply the polishing agent to the machined surface�

• Attach polishing sponge 11 to the sanding plate 8 in

the manner described above�

• Turn on the power tool and spread the polishing

agent on the machined surface� Subsequently, per-

form the polishing with circular or cross movements

with little pressure�

The manufacturer reserves the possibility to introduce changes.

• Turn off the power tool, remove polishing sponge 11

and attach polishing bonnet 12 to sanding plate 8�

• Using a soft cloth, remove excess polishing agent

from the machined surface and perform final polishing

with polishing bonnet 12, with circular or cross move-

ments with little pressure�

• After the work is completed, rinse polishing

sponge 11 and polishing bonnet 12 in warm water with

a cleaning agent� Do not use solvents.

• Squeeze (do not wring) polishing sponge 11 and

polishing bonnet 12� Allow them to dry, stretching them

on flat surface, adhesive surface on the bottom. Atten-

tion: do not store the polishing accessories unless

they have dried out completely.

Power tool maintenance / preventive

measures

Before carrying out any works on the power tool it

must be disconnected from the mains.

Cleaning of the power tool

An indispensable condition for a safe long-term exploi-

tation of the power tool is to keep it clean� Regularly

flush the power tool with compressed air thought the

ventilation slots 3�

After-sales service and application service

Our after-sales service responds to your questions

concerning maintenance and repair of your product as

well as spare parts� Information about service centers,

parts diagrams and information about spare parts can

also be found under: www.crown-tools.com�

Transportation of the power tools

• Categorically not to drop any mechanical impact on

the packaging during transport�

• When unloading / loading is not allowed to use any

kind of technology that works on the principle of clamp-

ing packaging�