Tips And Tricks; Troubleshooting - Metabo SE 2500 Originalbetriebsanleitung

Continuous activation: With the trigger (3)
pressed, push in the locking button (4) and
release the trigger. Press and release the trigger
again (3) to switch off.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
7.3 Screwdriver bit change
Inserting and removing the screwdriver bit:
- Remove the depth stop (12).
- Insert: Insert the screwdriver bit (13) in the bit
holder (14).
- Remove: Pull the screwdriver bit (13) from the bit
holder (14) using a pliers.
- Attach the depth stop (12) again:
turn and engage in position when mounted.
Note:
The bit holder (14) may be removed from the
screwdriver spindle if the sleeve (16) is pulled back.
Never use 25 mm long screwdriver
bits (13) in the screwdriver spindle
(15)! Removal is not possible! Only
use the bit holder (14)!
7.4 Working with depth stop
See page 2, illustration 2 a and 2 b.
To preset the screw insertion depth, one of the
screws to be inserted is fitted on the screwdriver bit
(13). Set the depth stop (12) by turning as follows:
a) Screws with heads designed to sit on top of the
material (socket-head screws, oval head screws,
hex screws):
the surface area of the screw head is 2 mm outside
the stop sleeve (17).
b) Flat head screws:
the area of the screw head is 2 mm outside the stop
sleeve (17).
Insert a screw as a test. Correct the screw depth if
necessary:
When the depth stop (12) is inserted, the insertion
depth changes by 0.25 mm per notch. If screw
insertion has to be deeper: Insert stop sleeve If the
screw insertion is too deep: Unscrew stop sleeve.
Removal of the depth stop (12) does not alter the
set screw insertion depth. After refitting, work can
continue at the same insertion depth.
When screwing in crosshead screws, press
the machine with the screwdriver bit (13) firmly
against the screw until the screw is fully inserted;
otherwise the bit could slip out of the cross recess
and damage the material.
7.5 Working without depth stop (12)
Adapt the speed of the screwing process by
carefully pressing in the trigger switch.
When the screwing process is complete, switch off
the machine by releasing the trigger switch (3).
7.6 LED lamp (depending on the model)
For working in badly lit areas. The LED light (6)
lights up when the machine is switched on.

8. Tips and Tricks

Press the machine firmly against the screw until the
screwing process is complete.
This is particularly important when inserting dry wall
screws (with coarse threads) in gypsum
plasterboards because the large thread pitch of the
screws means that they are very quickly inserted.
If the stop sleeve (17) is stiff, it can be removed to
clean the thread.
.

9. Troubleshooting

If the screwdriver bit (13) is fitted very firmly in the bit
holder (14): remove the screwdriver bit with a pair of
pliers.
9.1 Only for cordless machines; the
machine's multifunctional monitoring
system
If the machine switches off automatically, the
machine electronics have activated automatic
protection mode.
In spite of this protective function, overloading
is still possible with certain applications and
can result in damage to the machine.
Causes and remedies:
1. Battery pack almost flat (the electronics
prevent the battery pack from discharging totally
and avoid irreparable damage).
If one LED is flashing, the battery pack is almost
flat. (10) If necessary, press the (11) button and
check the LEDs (10) to see the charge level. If
the battery pack is almost flat, it must be
recharged.
2. Long continuous overloading of the machine will
activate the temperature cut-out.
Leave the machine or battery pack to cool.
Note: If the battery pack feels very warm, the
pack will cool more quickly in your "AIR
COOLED" charger.
Note: The machine will cool more quickly if you
operate it at idling speed.
3. If the current is too high (for example, if the
machine seizes continuously for long periods),
the machine switches off.
Switch off the machine at the trigger switch (3).
Then continue working as normal. Try to prevent
the machine from seizing.
ENG
10. Maintenance
Disconnect the mains plug or remove the battery
pack from the machine before starting any
maintenance work.
Remove the depth stop (12) regularly and clean it
ENGLISH en
11