grandimpianti WF6 Gebrauchsanweisung Seite 18

www.groupdynamics-laundry.com
sales@groupdynamics.lv
Press "PROG" again to pass on to "F2", and
so on to the last function, "L0".
Press "PROG" once more to exit the
programming mode and save the changes.
Programming will be confirmed a long beep.
WARNING: if a potential drop should
occur during a programming session,
changes will not be saved and it will be
necessary to repeat the programming
procedure from the beginning.
When a cycle is underway, the "PROG" key
causes the machine to pause and does not
give access the programming mode.
The PROG key so stops the cycle at whatever
stage except the spinning step.
The DISPLAYS will then read "PAUSE"
and the machine will stay like this until the
"START" key is pressed and the cycle is
resumed.
Attention!
-)This function is available only when a
cycle is in progress.
-)Pauses cause heating to go off too, which
means that long stops will cause the
temperature to drop.
PROGRAMMING
Options F0 to F9 and Ci and L0 can be
enabled singly and cycle by cycle. Functions
stay enabled permanently until the user
chooses to disable them.
The programming mode can be accessed
only with the door closed and with non coin-
operated machines.
During programming, the cycle display reads
the selected cycle (from 1 to 9), whereas the
time display reads "Fy", where y is the
function to be selected by the PROG key.
The temperature display will read the options
available for the currently selected function.
If the value is 0, the function is disabled,
whereas it is enabled when set to 1; F3 and
L0 envisage a third alternative : setting 2
(see specific description for F3 and L0).
The options available for every function are
changed using the "+" and "-" keys
respectively.
Press "P" key to select the cycle to be
modified.
When the PROG key is pushed repeatedly,
options are shown in a cyclic sequence from
F1 to L0 and then back to the current selection.
When the "P" key is pushed repeatedly, the
stored cycles appear (from 1 to 9).
IMPORTANT !!!
When an option is selected for a cycle that
does not envisage it (see description of each
option) the machine will accept the selection
but the corresponding function will not be
carried out.
PROGRAMMIMG BY PC
Washers can also be programmed via PC,
though a serial port. To this purpose the
washers feature an ad-hoc RS232 serial port
at the rear.
To enable the "data transmission and reading"
mode it will be necessary to switch the
washer on while holding down the "PROG"
key: the displays will only read "HC".
For further details, contact your seller or the
after-sales service.
CAUTION!
Do not try to read or change machine
programming, unless you have the ad-
hoc cable supplied by the manufacturer,
as this could cause severe damage to the
electronic boards.
If you wish to change machine programming,
contact your seller or the after-sales service.
DESCRIPTION OF PROGRAMMABLE
FUNCTIONS
Enabling draining (F0)
As a rule, the tub is drained at the end of the
steps featuring water intake, in preparation
for the next step. The programming software
can overrun the draining step so that the
cycle may pass on to the next wash step with
water in the drum. This option is useful, for
instance, when heating in various stages, to
start spinning with water in the drum or drain
during the speed-up. This procedure is carried
out when this parameter is set to "1", and the
selected cycle features it.
Value Function
0 Draining is performed always
1 Normal (default).
This function can be enabled for every single
cycle.
In standard programming, only the last rinse
step does not drain the water, so that the last
spin may be started with water in the tub,
which will be drained as soon as the machine
has distributed the wash load.
Cool-down (F1)
As a rule at the end of a high-temperature
wash cycle (above 60°C) cold water is taken
in in order for the temperature inside the
drum to decrease gradually. When this
parameter is set to "1", and the selected cycle
features it, this procedure is not carried out.
Value Function
0 Normal (default)
1 NO cool-down
18
This function can be programmed cycle by
cycle.
Shorter spinning (F2)
Effective final spinning time can be set to 1
minute or eliminated altogether. Effective
spinning time means the maximum high-
speed time. The speeding up is not affected
by this function.
Value Function
0 Normal (default)
1 1 minute spinning
2 No spinning
This function can be programmed cycle by
cycle.
No prewash (F3)
When this function is enabled the prewash
step is excluded.
Value Function
0 Normal (default)
1 No prewash
This function can be enabled for every single
cycle.
Cycle deferred start (F4)
Postpones the start of a wash cycle and
determines cycle delay.
If the value assigned to this function is other
than zero, as soon as the programming session
is exited the time DISPLAY will blink the
hours and the temperature DISPLAY will
blink the minutes, whereas the program
display will read the selected wash cycle.
To start the countdown, just press the START
push-button: the displays will be lit
continuously.
As soon as the countdown is over, the cycle
will start automatically and the displays will
resume their usual functions.
Before the START push-button is pressed
and during the count-down all keys are
enabled.
IMPORTANT !!!
Time is displayed in the "HH.MM"format.
H stands for hours and M for tens of minutes.
Unit: hours and minutes
Range: 00 h 00'...23 h 50'
(00.00...23.50)
Resolution: 10 minutes (0.1)
h
Default: 00 00'
CAUTION:
When an automatic deferred start is cancelled
(by reprogramming F4 to 00), the door lock
will enabled to open and it will be possible to
do so using the "P" key.
Enable/Disable buzzer(F5)
This function enables/disables the buzzer,
which can be completely eliminated from all
cycles except for alarms.
Value Function
0 Normal (default)
1 No buzzer