Control Elements And Connections - Monacor PA-1120DMT Einbau- Und Bedienungsanleitung

Message Storage Insertion
Module with Radio Clock
These instructions are intended for technicians
installing the module and for users without any
specific technical knowledge . Please read the in-
structions carefully prior to operation and keep
them for later reference .
All operating elements and connections de-
scribed can be found on the fold-out page 3 .
Contents

Control Elements and Connections . 14

1
2 Safety Notes . . . . . . . . . . . . . 15
Applications . . . . . . . . . . . . . 15
3
3 .1 Storage capacity . . . . . . . . . . . 16
Installation and Connections . . . . 16
4
4 .1 DCF77 module (fig . 2) . . . . . . . . . 16
Basic Settings . . . . . . . . . . . . 17
5
5 .1 Selecting the emergency trigger signal . 17
5 .2 Selecting the replay mode . . . . . . . 17
5 .3 Setting the clock manually . . . . . . 17
5 .4 Increasing the output level . . . . . . 17
6 Operation . . . . . . . . . . . . . . 18
6 .1 Recording . . . . . . . . . . . . . . . 18
6 .1 .1 Storage locations M1 - M6 . . . . . 18
6 .1 .2 Storage locations Voice01 - Voice20 . 18
6 .2 Replay . . . . . . . . . . . . . . . . 19
6 .2 .1 Storage locations M1 - M6 . . . . . 19
6 .2 .2 Calling up a message by
remote control . . . . . . . . . . . 19
6 .2 .3 Storage locations Voice01 - Voice20 . 20
6 .3 Deleting a message . . . . . . . . . . 20
6 .4 Message sequence . . . . . . . . . . 20
6 .4 .1 Programming a message sequence . 20
6 .4 .2 Replaying a message sequence . . . 21
6 .5 Time-controlled replay . . . . . . . . . 21
6 .5 .1 Creating a schedule . . . . . . . . . 21
6 .5 .2 Changing or deleting program data . 22
6 .5 .3 Copying a day schedule . . . . . . . 22
6 .6 Memory card . . . . . . . . . . . . . 22
6 .6 .1 Replaying an audio file . . . . . . . 22
6 .6 .2 Copying an audio file . . . . . . . . 23
Specifications . . . . . . . . . . . . 23
7
14
1 Control Elements and
Connections
1 Button PLAY/ REC to switch between replay
and recording for the messages M1 - M6
2 Control REC LEVEL to adjust the recording level
3 Headphone connection PHONES (3 .5 mm jack;
mono, left side only for stereo headphones),
minimum impedance of the headphones 64 Ω
When this jack is used, the output "Audio
Out" (26) to the amplifier will be muted .
4 Display
5 Slot for a memory card (type "microSD")
6 Button ENTER to call up a menu item and to
confirm an entry
7 Audio input (2-pole 3 .5 mm jack) to connect
a microphone or an audio source with line
output level for recording a message
8 Recessed reset button for the microprocessor
of the insertion module (use a thin, non-con-
ductive object to press the button)
The processor will be reset (as it is after the
power supply was interrupted) . This reset will
not apply to the message memory and the
program memory .
9 Switch MIC / LINE to select the input sensitivity
for the audio input (7)
10 Button MENU to call up or cancel a setting
menu
11 Button DN to reduce the number of repeats
for the replay of a selected message, to select
a menu item and to reduce a value to be set
12 Button UP to increase the number of repeats
for the replay of a selected message, to select
a menu item and to increase a value to be set
13 Button REPEAT/ STOP to start and stop the re-
play of a message M1 - M6 with the repeats
set
14 Button START/ STOP to start and stop the one-
time replay of a message M1 - M6
15 Buttons M1 - M6 to select a storage location
for recording or replaying a message
16 Control LEVEL to adjust the volume of the
replay
17 DCF77 radio clock receiver
18 Connection plate to be mounted on the rear
side of the amplifier
19 Jumper J1 to adjust the output level
(position hi = +10 dB)