Scheppach ASP30 Originalbetriebsanleitung Seite 14

- Foam filter (Fig.1/Pos.20): suitable for wet vacuum-
ing
- HEPA filter (Fig.1/Pos.21): suitable for dry vacuum-
ing
Installing the hose
Dry vacuuming:
1. Insert the HEPA filter (Fig.1/Pos.21).
2. Push the vacuum hose (3) onto the vacuum nozzle
(3) and turn this clockwise. (Fig.1)
3. Insert the cover for the hose connection (13) into
the wet vacuuming connection. (Fig.9).
Wet vacuuming
1. Insert the foam filter (Fig.1/Pos.21).
2. Push the vacuum hose (2) into the connection on
the water tank (11) and turn this clockwise.
3. Insert the hose connection cover (Fig.1/13) into the
dry vacuuming connection
Air blasting
4. Ensure that the water tank (Fig.1/Pos11) is com-
pletely drained and clean.
5. Push the vacuum hose (Fig.1/Pos.2) into the blast
nozzle (Fig.1/Pos.16) and turn this clockwise
Extraction unit for electrical devices
1. Connect the dust extraction unit (Fig.1/Pos. 22) to
the electrical device and the vacuum hose (Fig.1/
Pos.2).
2. Push the vacuum hose (Fig.1/Pos.2) onto the vacu-
um nozzle (Fig.1/Pos.3).
3. Plug the electrical device's plug into the socket
(Fig.1/Pos.7).
Assembling accessories
1. After connecting the vacuum hose (Fig.1/Pos.2),
push the handle (Fig.1/Pos.19) into the telescopic
vacuum pipe (Fig.1/Pos.14).
2. Press the unlock button for the telescopic vacuum
pipe (Fig.1/Pos.17) to extend the telescopic vacu-
um pipe (Fig.1/Pos.14).
Installing brushes and nozzles
1. Select the brush or nozzle suitable for the relevant
job
2. Push the telescopic vacuum pipe (Fig.1/Pos.14)
into the required brush or nozzle
Floor nozzle (Fig.10) – to vacuum carpets (setting
A) and hard surfaces (setting B). Also suitable for wet
vacuuming.
Joint nozzle (Fig.1/Pos.23) – for locations that are
difficult to access, e.g. edges, radiators.
Brush nozzle (Fig.1/Pos.24) – to remove dust from
highly sensitive pieces of furniture or items suscepti-
ble to scratching.
14 І 88
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
Operation
Switching on
Tip the on/off switch (Fig.1/Pos.15) into the ─ posi-
tion to switch the device on.
Switching off:
Tip the on/off switch (Fig.1/Pos.15) into the 0 position
to switch the device off.
Switching on with an electrical device connected:
Tip the on/off switch (Fig.1/Pos.15) into the ═ posi-
tion to switch the device and the connected electrical
device on.
Speed regulation
The vacuuming force can be adjusted using speed
regulation (Fig.1/Pos.5).
- Turn speed regulation clockwise to increase the
speed and suction force.
- Turn speed regulation
to reduce the speed
Dry vacuuming (Fig.1)
m Warning! Pull out the mains plug before car-
rying out any adjustments, maintenance or repair
work.
Dry vacuuming
- Ensure that the dust bag (25) is installed.
- Fill the water tank (11) up to the line
- Affix the hose connection cover (13) to the water
tank (11).
- Loosen the quick coupling (8) on both sides of the
device and remove the machine head.
- Install the HEPA filter (21).
- Re-attach the machine head to the water tank (11).
- Fit the vacuum hose (2) to the machine head.
- Select the required brush or nozzle.
Wet vacuuming (Fig.1)
- Remove the dust bag (24).
- Fasten the cover (13) for the hose connection on
the machine head.
- Install the vacuum hose (2) with the floor nozzle
(12) on the water tank (11.
- Loosen the quick coupling (8) on both sides of the
device and remove the machine head.
- Install the foam filter (20).
- Re-attach the machine head to the water tank (11).
Automatic mode
- Plug your electrical tool's cable into the socket
(Fig.1/Pos.7).
- Connect the vacuum hose (Fig.1/Pos.2) to the dust
vacuuming connection on your electrical tool. En-
sure that the device connections are air tight.
- Tip the on/off switch (Fig.1/Pos.15) into the ═ posi-
tion.
- The wet and dry vacuum cleaner switches on as
soon as the electrical tool is switched on. When
you switch your electrical tool off, the wet and dry
vacuum cleaner switches off with the preset delay
anticlockwise
and suction force