Safety Warnings; System Components - STEINEL HF 360 COM 1 Bedienungsanleitung

GB Operating instructions
Dear Customer,
Congratulation on purchasing Please familiarise yourself with
your new STEINEL presence de- these instructions before at-
tector and thank you for the tempting to install the presence
confidence you have shown in detector because prolonged, re-
us. You have chosen a high-qual- liable and trouble-free operation
ity product that has been manu- will only be ensured if it is fitted
factured, tested and packed with and used properly.
the greatest care.

Safety warnings

L Disconnect the power supply L Installing the sensor involves
before attempting any work work on the mains power
on the sensor! supply. This work must there-
L During installation, the elec-
fore be carried out profes-
tric power cable to be con- sionally in accordance with
nected must be dead. There- the applicable national wir-
fore, switch 'OFF' the power ing regulations and electrical
first and use a voltage tester operating conditions (VDE
to make sure the wiring is off 0100).
circuit.
Assembly/Installation m (see chart on page 2)
The sensor is only intended for Sensor and load module come
concealed, indoor installation in ready assembled and must be
ceilings (apart from the COM 1 plugged together after fitting
AP - surface-mounted - option). the load module and setting the
A clamping-type ceiling adapter potentiometers/dip switches.
or surface-mounting adapter is
not included.

System components

a Load module e Twilight setting
b Sensor module f Time setting
c Sensor base Switching output 1
d Dip switches g HVAC stay-'ON' time
(1) Normal/test mode Switching output 2
(2) Semi-/fully automatic h HVAC switch-'ON' delay
mode Switching output 2
(3) Button/switch i Reach setting
(4) 'ON' / 'ON'-'OFF' button j Clamping-type ceiling
(5) DIM option adapter, optional
Constant lighting control
'ON'/'OFF'
We hope your new STEINEL
sensor will bring you lasting
pleasure.
L It is only permissible to use
electronic ballasts with isola-
ted control signal at the DIM
1-10 V control output.
Accessories:
Clamping-type ceiling adapter,
EAN no.: 4007841 000370
Surface-mounting adapter,
EAN no.: 4007841 000363
Guard cage,
EAN no.: 4007841 003036
Service remote control,
EAN no.: 4007841 000387
User remote control,
EAN no.: 4007841 003012
k Surface-mounting adapter
IP 54, optional
l Locking mechanism
m Assembly/Installation
n Parallel-connected
configurations
o Stay-'ON' time
Orientation light
DIM option
p Film shroud for minimising
the detection zone (HF 360).
- 20 -
How it works / Basic function
The high-frequency presence cy technology guarantees that
detectors from the Control PRO movement is detected absolute-
range control lighting as well as ly anywhere irrespective of radi-
heating, ventilation and air-con- ated temperature. Sensing
ditioning (COM 2 only), e.g. in of- movement in two directions, the
fices, WCs, public buildings or at DUAL HF sensor is ideal for corri-
home, in relation to ambient dors in hotels, schools and office
light level and the presence of buildings. The presence detec-
persons. Modern, high-frequen- tor's switching outputs and
Presence Control PRO Presence Control PRO
HF 360 COM 1 / COM 1 AP HF 360 COM 2
DUAL HF COM 1 / COM 1 AP
1 switching output, such as
1 switching output operating COM 1. Plus a 2nd switching
in relation to brightness setting output for HVAC (heating /
and presence of persons. ventilation / air conditioning)
governed by presence.
Settings:
- Brightness setting Settings:
- Stay-'ON' time, pulse mode, - Stay-'ON' time
IQ mode - Switch-'ON' delay
- Room surveillance
Detection zone
HF 360 mounting height 2.8 m
The reach of the HF 360 is electronically adjustable.
1 or 2 detection directions can be masked out for
adjustment to the room situation. An angle of cov-
erage of 360° provides a max. reach of 8 m.
reach are set at the potentio-
meters and dip switches or by
means of the optional remote
control. Presence Control has
a low intrinsic power consump-
tion.
Presence Control PRO
HF 360 DIM
DUAL HF DIM
1 switching output operating
in relation to brightness setting
and presence of persons.
Settings:
- Brightness setting
- Stay-'ON' time, IQ mode
- Orientation light
- Constant lighting control
DUAL HF mounting height 2.8 m
The DUAL HF sensor has 2 special HF sensors that
detect movement from the ceiling in both direc-
tions. Controlled electronically, reach is infinitely
variable in both directions from 3 × 3 m – 10 × 3 m.
- 21 -