Installation - EMAK PW 121C Bedienungsanleitung

3.2 s a
tandard
Make sure that in the product package that was bought there are the following elements:
• high-pressure water cleaner (PW 121C - PW 136C - PW 145C - IP 1210S - IP 1360S - IP 1450S);
• high-pressure delivery pipe with fast coupling;
• water brush (PW 136C - PW 145C - IP 1360S - IP 1450S only);
• lance hose;
• rotating nozzle head (PW 136C - PW 145C - IP 1360S - IP 1450S only);
• nozzle support head
• foaming lance;
• use and maintenance manual;
• nozzle cleaning pin;
• handlebar;
• 2 screws to secure handle,
In case of problems, apply to the dealer or to an authorised service centre.
3.3 o a
ptIonal
The standard accessories for the high pressure cleaner can be integrated with the following vast range of
accessories:
• Sandblasting lance: designed for smoothing down surfaces, eliminating rust, paint, deposits etc.
• Pipe-draining probe: designed for unblocking pipes and ducts.
• Rotating water jet brush: designed for cleaning delicate surfaces.
• floor cleaning lance.
WArnIng
• The operation of the water cleaner may be impaired if unsuitable accessories are used and they may even make
it dangerous. Only use original accessories endorsed by the Manufacturer.
Refer to the documents provided with the optional accessories for information regarding their general use, safety
warnings, installation and maintenance.
4 I
nstallatIon
4.1 a
ssemblInG
a) Insert the handling bar (3) onto the body of the high pressure cleaner. Make sure you fully insert the bar into the
high-pressure cleaner's body (the front surfaces must be aligned with one another). Secure the bar with the 2 screws
supplied (cross head screwdriver not supplied). Step A in fig. 2
b) The version are supplied with a lance hose (28) which can be fitted with a standard nozzle support head (27), or a
head with a rotating nozzle (18), using a bayonet mount.
Depending on the job to be done, fit one of the two heads by inserting it into the lance hose and turning it clockwise
until it clicks securely onto the coupling. Now block it in place with the Securfix ring nut (11), by turning it
clockwise. Step I in fig. 2.
To remove the head, turn the Securfix ring nut (11) anti-clockwise and remove it. Keep the head pressed down into
the lance hose housing and turn it anticlockwise until it is released, then remove it completely. Step h in fig. 2.
c) Unroll the high-pressure hose (23), connect the quick-fit connector (24) to the water outlet connector (8), screw
down and secure. Step c in fig. 3.
d) Screw the end of the high pressure hose (23) (the end without the quick fit connector) onto the thread of the spray
gun (14) and secure it tightly using two 17 mm socket keys (not supplied). Step d in fig. 3.
4.2 C
heCks and
cAUtIon
• The water supply must be able to guarantee the adequate delivery of water flow to the high pressure cleaner; refer
to the table of technical specifications.
In case of doubt, contact a Skilled technician.
• Do not supply the water cleaner with water at a temperature in excess of 40°C/98°F or below 5°C/41°F.
• The pressure of the water supply must not be in excess of 8 bar/116 psi.
• Do not operate the high pressure cleaner with a priming depth in excess of 0 m/0 ft.
• Do not operate the high pressure cleaner if it is not connected to a water supply.
20
• Do not supply the high pressure cleaner with salt water or water containing impurities. In this event, run the high
CCessorIes
CCessorIes
a
the CCessorIes
C
onneCtIon to the
m W s
aIns ater upply