Use; Battery Check/Setting On A New Machine - Nilfisk-Advance BR 601 Betriebsanleitung

USE

WARNING!
On some points of the machine there are some
adhesive plates indicating:
– DANGER
– WARNING
– CAUTION
– CONSULTATION
While reading this Manual, the operator must pay particular
attention to the symbols shown on the plates.
Do not cover these plates for any reason and immediately
replace them if damaged.
BATTERY CHECK/SETTING ON A NEW
MACHINE
WARNING!
The electric components of this machine can
be seriously damaged if batteries are either
installed or connected improperly. The
batteries must be installed by qualified
personnel only. Set the function electronic
board and the built-in battery charger
(optional) according to the type of batteries
used (WET or GEL).
Check the batteries for damage before
installation.
Disconnect the battery connector and the
battery charger plug.
Handle the batteries with great care.
Install the battery terminal protection caps
supplied with the machine.
The machine requires one of the followings:
– One 24 V battery box, 240 Ah/C5 (WET)
– One 24 V battery box, 240 Ah/C5 (GEL) (optional)
– 4 6 V batteries, 180 Ah C5 (WET)
– 4 6 V batteries, 180 Ah C5 (GEL)
The machine can be supplied in one of the following modes:
a) Batteries (WET or GEL) already installed on the
machine and ready to be used.
1. Lift the covers (1 and 13, Fig. I) and check that the tanks
(15 and 16) are empty, otherwise drain them through the
drain hose (10, Fig. C) and the tap (24).
2. Close the covers (1 and 13, Fig. I).
3. Carefully lift the tank assembly (1, Fig. J).
4. Check that the batteries are connected to the machine
with the connector (4, Fig. J).
5. Carefully close the tank assembly (1, Fig. J).
6. Insert the ignition key (12, Fig. B) and turn it to "I". If the
green warning light (7a, Fig. B) turns on, the batteries
are ready to be used. If the yellow or red warning light
(7b or 7c, Fig. B) turns on, it is necessary to charge the
batteries (see procedure in Maintenance chapter).
909 6160 000(2)2006-10 A
b) Batteries (WET) installed on the machine but without
electrolyte.
1. Lift the covers (1 and 13, Fig. I) and check that the tanks
(15 and 16) are empty, otherwise drain them through the
drain hose (10, Fig. C) and the tap (24).
2. Close the covers (1 and 13, Fig. I).
3. Carefully lift the tank assembly (1, Fig. J).
4. Remove the caps (5, Fig. J) of the batteries (2).
WARNING!
Pay attention when using sulphuric acid, as it
is corrosive. If it comes in contact with skin or
eyes, rinse thoroughly with water and consult
a physician.
Batteries have to be filled in a well-ventilated
area.
Wear protective gloves.
5. Fill up the battery cells with sulphuric acid for batteries
(density 1.27 to 1.29 kg at 25°C) as shown in the Battery
Manual.
The correct quantity of sulphuric acid is shown in the
Battery Manual.
6. To avoid damaging the floor, dry with a cloth both acid
and water on the top of the batteries after charging.
7. Let the batteries rest and fill in with sulphuric acid as
shown in the Battery Manual.
8. Charge the batteries (see the procedure in Maintenance
chapter).
c) Without batteries
1. Buy appropriate batteries (see the Technical Data
paragraph).
For battery choice and installation, apply to qualified
battery Retailers.
2. Set the machine and the battery charger (if equipped)
according to the type of batteries installed (WET or
GEL).
3. Install the batteries.
4. Charge the batteries.
USER MANUAL
9