Preliminary Checks - BFT DEIMOS 800F Gebrauchsanleitung

ENGLISH
Cloning a transmitter means creating a transmitter which can be automatically
included within the list of the transmitters memorised in the receiver, either
as an addition or as a replacement of a particular transmitter.
Cloning by replacement is used to create a new transmitter which takes the
place of the one previously memorised in the receiver; in this way a specific
transmitter can be removed from the memory and will no longer be usable.
Therefore it will be possible to remotely program a large number of additional
transmitters or, for example, replacement transmitters for those which have
been lost, without making changes directly to the receiver.
When coding safety is not a decisive factor, the on-board receiver allows
you to carry out fixed-code additional cloning which, although abandoning
the variable code, provides a high number of coding combinations, there-
fore keeping it possible to "copy" any transmitter which has already been
programmed .
12) RADIO-TRANSMITTER CLONING (Fig.20)
Rolling-code cloning / Fixed-code cloning
Make reference to the universal palmtop programmer
CLONIX Programming Guide.
12.1) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS
Make reference to the universal palmtop programmer
CLONIX Programming Guide.
13) ACCESSORIES
SPL (fig.22).
Pre-heating optional board. Recommended for temperatures below -10°C.
(In the case of hydraulic motors).
ME (fig.23).
Optional board used to connect a 12Vac electric lock.
EBP (fig.16).
The EBP electric lock with continuous service can be connected directly to
terminals 1 and 4.

14) PRELIMINARY CHECKS

Before proceeding to any installation work, check that the gate structure
conforms to whatever is prescribed by the current standards, and in
particular that:
• The gate sliding track is linear and horizontal, and the wheels are suitable
for supporting the gate weight.
• The gate manual operation can be carried out smoothly along its entire
run, and there is no excessive side slipping.
• A correct play is provided between the upper guide and the gate to ensure
regular noiseless movement.
• The opening and closing gate stops are positioned.
• The established position for gearmotor fixing allows the emergency
manoeuvre to be carried out smoothly and safely. In the case where the
elements checked do not meet the above requirements, proceed to car-
rying out the necessary corrective actions or replacements.
WARNING: Remember that control devices are intended to facilitate gate
operation, but can not solve problems due to any defects or deficiency
resulting from failure to carry out correct installation or maintenance.
Take the product out of its packing and inspect it for damage. Should it be
damaged, contact your dealer. Remember to dispose of its components
(cardboard, polystyrene, nylon, etc.) according to the current prescriptions.
15) BASE PLATE ANCHORING
15.1) Standard position
• Dig a hole where the cement pad with the buried base plate log bolts is to
be placed in order to fix the reduction gear unit (fig.3). If the sliding track
is already there, digging must be partly carried out in the track foundation
casting. This way, should the track foundation casting sag, the gearmotor
base would also lower, thus maintaining the play between pinion and rack
(approximately 1-2 mm).
• Position the base plate according to the dimensions specified in fig.4.
• The pinion symbol printed on the base plate must be visible and directed
towards the gate. This also ensures the correct positioning of the raceways
for electrical connections.
• Let the flexible pipes containing electrical cables protrude from the
base plate.
• In order to keep the base plate in its correct position during installation,
it may be useful to weld two iron flat bars under the track, and then weld
the log bolts onto them (fig.3).
• Make a concrete casting in such a way as to embody the base plate
casting into that of the gate track.
16 -
DEIMOS - DEIMOS 700 - DEIMOS 800F Ver. 04
INSTALLATION MANUAL
• Accurately check that:
The positioning dimensions are correct.
That the base plate is well levelled.
That the 4 stud threads are well clear of cement.
Let the casting harden.
15.2) Other positions
The gearmotor can be positioned in different ways. In the case where the
gearmotor is not fixed on the level of the sliding track (Standard position),
you must ensure that the gearmotor is tightly secured also in relation to the
gate position, so as to maintain a correct play (1-2mm) between rack and
pinion. The current safety standards with respect to persons, animals and
things must be strictly observed, and in particular risks of accidents due to
squashing in the area of pinion-rack meshing, as well as other mechanical
risks, must be carefully avoided.
All the critical spots must be protected by safety devices in compliance
with the current prescriptions.
Instructions and the
16) GEARMOTOR FIXING
When the casting has hardened, observe fig. 6 and proceed as follows:
• Position an M10 nut on each of the tie rods, keeping a distance of at
Instructions and the least 25mm from the base to allow the gearmotor to be lowered after
the installation is completed, or for subsequent adjustments of the play
between pinion and rack.
• Position a plate "P" supplied as standard on each pair of tie rods and,
with the help of a level, adjust the plane in both directions.
• Remove the screw-cover guard from the gearmotor, and position the reduc-
tion gear unit on the four tie rods with the pinion facing the gate.
• Position the four washers and screw the four gearmotor locking bolts.
• Adjust the depth of the gearmotor, making it slide in the appropriate slots
found in the base, and fix it at a distance between pinion and gate which
is adequate to the type of rack to be installed. The rack teeth must mesh
into the pinion along their entire width. In the paragraph headed "Rack
fitting" we specify the measurements and installation methods of the
most widely used types of rack.
17) RACK FITTING
A rack having a 4 tooth pitch must be fitted to the gate. As far as the length
is concerned, this must include the passage space, as well as the space for
securing the brackets activating the limit microswitches, and for the pinion
meshing section. There are different types of rack, each one differing in
terms of capacity and gate fixing method. The Company markets three
types of racks, which are.
17.1) Mod. CFZ (Fig.7).
Galvanised iron rack - 22x22mm section - supplied in 2 - metre lengths -
capacity over 2000kg (≈ 20000N). First weld these pieces onto an adequate
iron angle bar and then weld the lot to the gate. Besides maintaining the
distance between the rack and the side of the gate, the angle bar makes
it easy to fix the rack to the gate, even when the latter is subject to slight
side slipping. When join welding the various rack pieces, you are advised
to arrange a section of rack as in (fig.8) to ensure a correct pitch along the
entire length of the rack.
17.2) Mod. CPZ (Fig.7).
Plastic rack - 22x22mm section - supplied in 1- metre lengths - max. capacity
500kg (≈ 5000N). This model is to be fixed to the gate by means of normal
or self-threading screws. Also in this case, you are advised to insert a sec-
tion of rack the other way round in the joint between the various pieces,
so as to maintain the correct tooth pitch. This type of rack is quieter and
allows height adjustments to be made even after having been fixed, using
the slots provided.
17.3) Mod. CVZ (Fig.7)
Galvanised iron rack - 30x12mm section - supplied in 1 - metre lengths -
threaded spacers to be welded - max. capacity 2000kg (≈ 20000N). Having
fixed the spacers in the middle of each of the slots in the various rack pieces,
weld the spacers to the gate. Also in this case, arrange a section of rack the
other way round in the joining points of the various rack pieces to ensure a
correct tooth pitch. The screws which fix the rack to the spacers allow the
rack to be adjusted in height.
17.4) Rack fitting
To fit the rack, proceed as follows:
• Activate the emergency release by rotating the appropriate release knob
(See paragraph "Emergency manoeuvre").
• Rest the rack end on the control pinion and secure it (by welding or using
screws) in correspondence with the pinion, while sliding the gate along