Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
All operating elements and connections described
can be found on page 2.
1 Operating Elements and Connections
1.1 Monitor
1 Button
to switch on the monitor or to switch to
the stand-by mode
2 Button V1/ V2 to switch over the video sources
3 Button MENU to activate the menu items of the
on-screen menu
4 Buttons + and - for adjustments in the on-screen
menu
5 3.5 mm jack VIDEO for connection of two video
sources via the supplied distribution cable with
RCA plugs
6 Power supply jack 12 V
power supply unit provided
7 IR sensor for the remote control signals
1.2 Remote control
8 Button
: corresponding to button
monitor
9 Operating panel to adjust the image parameters:
Buttons
brightness
Buttons COL
colour intensity
Buttons
contrast
Increase (
L
) or reduce (
sponding arrow button.
10 Button V1\V2: corresponding to button V1/ V2 (2)
on the monitor
11 Button P.P to switch over different image adjust-
ments
12 Button SYS for mirror image mode:
R
R
R
2 Safety Notes
The units (monitor and power supply unit) correspond
to all relevant directives of the EU and are therefore
marked with
.
WARNING
The power supply unit uses dangerous
mains voltage. Leave servicing to
skilled personnel only. Inexpert han-
dling or modification of the unit may
result in electric shock.
Please observe the following items in any case:
G
The units are suitable for indoor use only. Protect
them against dripping water and splash water, high
air humidity and heat (admissible ambient tempera-
ture range 0 – 40 °C).
G
Do not operate the monitor and immediately discon-
nect the power supply unit from the socket
for connection of the
(1) on the
M
) the value with the corre-
1. if the units are visibly damaged,
2. if a defect might have occurred after a unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case the units must be repaired by skilled per-
sonnel.
G
For cleaning only use a dry, soft cloth; never use
water or chemicals.
G
No guarantee claims for the units and no liability for
any resulting personal damage or material damage
will be accepted if the units are used for other pur-
poses than originally intended, if they are not cor-
rectly connected or operated, or if they are not
repaired in an expert way.
If the units are to be put out of operation
definitively, take them to a local recycling
plant for a disposal which will not be harmful
to the environment.
3 Applications
This TFT LCD colour monitor with LED background
illumination is suitable for universal applications, e. g.
in video surveillance systems. It has two video inputs
and offers a sharp image of high contrast in the format
16 : 9 or 4 : 3. The image can be mirrored vertically
and/or horizontally.
The monitor is supplied with:
– an infrared remote control,
– a monitor support
– a power supply unit
– an RCA adapter cable for the video connections
4 Setting Up / Installation
Set up the monitor via the support provided, consisting
of a base and a hinged bracket (fig. 4), or mount it to a
wall:
1) Release the mounting screw (b) on the bracket so
that the small metal plate (c) can be slid into the
guide rail (a) on the rear side of the monitor. Slide
the metal plate into the guide rail and tighten the
mounting screw to clamp the bracket to the guide
rail.
2) Screw the base to the bracket via its spring-loaded
recessed head screw (d). Tighten the screw in such
a way that a stable connection between the base
and the bracket is ensured.
3) Release the locking screw (e) on the hinge of the
bracket, adjust the desired inclination of the monitor
and retighten the screw.
4) For wall mounting, fasten the base with 2 screws
(fig. 6). Even when the support is standing on its
base (fig. 5), the base should be screwed to a sta-
ble place if tilting over or overturning of the monitor
cannot be excluded.
GB
7
Werbung
Inhaltsverzeichnis
