Reset; Replacing The Watch Battery; Battery Low Indicator; Wearing The Chest Belt - Crivit 1-LD3814 Bedienungsanleitung

Reset

The watch can be reset by pressing and holding SET and SEL together. Only after
reseting the watch the other language can be selected.

Replacing the watch battery

The battery replacement can be performed by a watch maker in addition to a
water resistance test.
To replace the battery yourself, please read the following instructions first:
Remove the screws (1, 2, 3 and 4) from the back side of the watch with a small
Phillips screwdriver. Remove the caseback and the battery sticker.
Use a small, flat tool to open the latch (5) of the battery holder. Remove the
battery and insert a fresh 3V CR2032 battery with the (+) terminal facing upwards.
Ensure that the gasket (6) is seated correctly. Close the latch of the battery holder.
Replace the battery sticker and the caseback and replace the screws.

Battery low indicator

If the battery voltage on the chest belt battery drops below the voltage required for
normal operation,
TXBELT TXGURT
LO BAT BATT
will appear on the display. Replace the battery of the chest belt as described in the
chapter "Chest belt".

Using the bicycle holder

The included bicycle holder can be used to attach the wrist watch to the handlebar
of a bicycle.
Press the bicycle holder onto the top of the handlebar. Handlebars with an
especially large diameter may require the use of additional force to snap on the
bicycle holder. The heart rate monitor can now be attached to the bicycle holder
in the same way that you would attach it to your wrist.
The maximum range of 70cm between the wrist watch and the chest belt should
not be exceeded.

Light

Briefly press LIGHT to temporarily activate the light.

Important notes on the operation of the wrist watch

3 different Modes of Operation.
The watch has
SNGLTX TXBCIN
PILE BAT BA
- 7 -
- 9 -

Wearing the chest belt

Adjust the chest belt so that it fits
snugly directly below the chest
muscles. Moisten the contact
areas with water or ECG gel
(ECG gel can be purchased at a
pharmacy). Ensure that the
contact areas constantly remain in
skin contact.
Position the chest belt as per the
following illustration.
Please ensure that the chest belt is
seated properly. When you have
exhaled completely the chest belt
should still have very slight tension
pressing it to your chest.
High voltage power lines, Trains
or moving vehicular traffic may
interfere with the heart rate
measurement. Please consider this
when planning your exercise
route.

Coded transmission

The chest belt's transmissions are digitally coded to prevent interference if you are
training with a training partner who is using an identical watch and chest belt.
When using the chest belt for the first time, a random channel is selected
automatically. The channel is briefly displayed at the top of the display upon
entering the heart rate display mode. The available channels are CH10, CH11,
CH12, CH13 and CH14.
The channel can be changed by briefly removing the battery from the chest best
and reinserting it. The chest belt will randomly select a channel and after approx. 1
minute the heart rate and the new channel will appear on the display of the watch.
Press MODE to select the mode of operation of the watch.
The order of the modes is as follows:

Time and basic settings

TIME ZEIT
Stop watch
CHRONO ST-UHR
Heart rate
HRM PULS
Each mode of operation may have several subfeatures.
The subfeatures can always be accessed by pressing SEL

Speed setting

When setting numerical values, press and hold SEL to use the speed setting
feature.
Time and basic settings
Press MODE to select the feature before proceeding.
TIME ZEIT
The subfeatures of the time mode can be accessed by pressing SEL.
Time and basic settings
TIME ZEIT
Alarm
ALARM ALARM
Timer
TIMER TIMER
contact area
- 8 -
TEMPS HORA
CHRONO CRONO
FC PULSO
SEL SEL. SEL
TEMPS HORA
TEMPS HORA
ALARM ALARMA
COMPTE TIMER
- 10 -