Maintenance - Velleman DVM205AM Bedienungsanleitung

4. Touc h the target sur
the L LCD.
f) P Period Measur
1. Plug the black test le
2. Set t the selection sw
3. Conn nect the black tes
be m easured.
4. Read d the measured
NOTE: Th he applied time
g) P Pulse Width M
1. Plug the black test le
2. Set t the selection sw
3. Conn nect the black tes
be m easured.
4. Read d the measured
h) R RPM Measurem
1. Plug the black test le
(#11 1).
2. Set t the selection sw
on th he RPMx10 rang
3. Conn nect the black tes
the re ed test lead to a
4. Crank k the engine; the
i) D Dwell Angle Me
1. Plug the black test le
(#11 1).
2. Set t the selection sw
on th he DWELL range
3. Conn nect the black tes
the re ed test lead to a
4. Crank k the engine; the
NOTE: The dwell ang
ignition system
to have the dw
7. Ma intenance
CAUTION N: Before openin
to avoid electric shock h
closed se ecurely.
If your D DVM205AM sho
not faulty y and are prope
a) I Install or Repl
The batte ery should be re
and open n the case. Rem
6F22 or e equivalent) - mi
b) R Replace a Fuse
The fuse rarely needs to
the screw ws at the back a
250V/10A A fast blow for
Use this s device with o
event of f damage or in
For mor e info concern
The info ormation in thi
© COPYR RIGHT NOTICE
This manu al is copyrighted.
No part of this manual may
the prior w written consent of
05.01.201 0
rface with the e xtremity of the
ements
ead in COM and d the red test lea
itch (#2) to "Pe eriod ms".
st lead to ground d and the red tes
value on the dis splay.
for most fuel in njectors is displa
easurements
ead in COM and d the red test lea
itch (#2) to "Pu ulse Width ms".
st lead to ground d and the red tes
value on the dis splay.
ments
ead in COM and d the red test lea
itch (#2) to the e applicable pos
ge).
st lead to the neg gative pole of the
breaker point.
e RPM (rotations s per minute) wil
easurements
ead in COM and d the red test lea
itch (#2) to the e applicable pos
e).
st lead to the neg gative pole of the
breaker point.
e dwell angle wil l be displayed.
le needs only be e tested in cars
m. Cars with an electronic ignit
well angle tested d.
ng the case, set t the selection s
hazard. Do not s switch the devic
ould not be oper rating properly,
erly inserted.
ace a Battery
eplaced when "B BAT" appears on
move the old bat tery (when repl
ind the polarity ! Close the case
e
o be replaced; a blown fuse is u
and open the ca se. Replace the
10A range), clo se the case and
original access sories only. Ve
njury resulted from (incorre
ning this produ uct, please vis
is manual is su ubject to chan
The copyright to o this manual is
be copied, reprod uced, translated o
the copyright hold der.
DVM20 5AM
probe and read
ad in the + con
st lead to the wire
ayed on the neg
ad in the + con
st lead to the wire
ad in the + con
ition (2, 4, 5, 6
e car battery and
l be displayed.
ad in the + con
ition (2, 4, 5, 6
e car battery and
with a tradition
tion system don
witch to OFF an
ce on before the
check the batte
n the display. Tu
lacing) and insta
e and tighten th
usually the resu
e old fuse (250V
d tighten the scr
elleman nv can
ct) use of this
sit our website
nge without pr
owned by Vellem
or reduced to any e
7
d the measured temperature fro
nector (#11).
e that connects t to the componen
gative (-) slope.
nector (#11).
e that connects t to the componen
nector
or 8CYL
d connect
nector
or 8CYL
d connect
nal
't need
nd disconnect al l test leads in o
e battery/fuse co ompartment doo
ery and fuses to o make sure the
urn loose the sc crews at the bac
all a new one (1 1 x 9V-battery t
e screws.
lt of the operato or's error. Turn
V/0.5A fast blow w for 400mA ran
rews.
nnot be held re esponsible in t
s device.
e www.vellema an.eu.
ior notice.
man nv. All worldw wide rights reserve
electronic medium or otherwise with
om
nt to
nt to
order
or is
ey are
ck
type
loose
nge;
the
ed.
hout
©Vellema an nv