Main Unit Display - Pioneer DJM-900NXS Bedienungsanleitung

g DIGITAL, CD/ LINE, PHONO, LINE, USB */* selector switch (page 13)
Select the input source of each channel from the components connected to this
unit.
h TRIM control (page 13)
Adjusts the level of audio signals input in each channel.
i EQ/ISO (HI, MID, LOW) controls (page 13)
These adjust the sound quality of the different channels.
j Channel Level Indicator (page 13)
Displays the sound level of the different channels before passing through the
channel faders.
k COLOR controls (page 14)
These change the parameters of the SOUND COLOR FX of the different
channels.
l Channel Fader (page 13)
Adjusts the level of audio signals output in each channel.
m CROSS FADER ASSIGN (A, THRU, B) selector switch (page 13)
Set the output destination of each channel to [A] or [B].
n Crossfader (page 13)
Outputs audio signals assigned by the crossfader assign switch correspond-
ing to the curve characteristics selected by [CROSS FADER] (Crossfader Curve
Selector Switch).
o MASTER LEVEL controls (page 13)
Adjusts the sound level output from the [MASTER] channel.
p Master Level Indicator (page 13)
Displays the sound level output from the [MASTER] channel.
q BALANCE controls (page 14)
Adjusts the left/ right balance of the sound output from the [MASTER1] termi-
nals, etc.
r MONO, STEREO selector switch (page 14)
Switches the sound output from the [MASTER1] terminals, etc., between mon-
aural and stereo.
s BOOTH MONITOR controls (page 14)
Adjusts the level of audio signals output at the [BOOTH] terminal.
t EQ CURVE (ISOLATOR, EQ) selector switch (page 13)
Switches the function of the [EQ/ISO (HI, MID, LOW)] controls.
u CH FADER ( , ,
Switches the channel fader's curve characteristics.
v CROSS FADER ( ,
This switches the crossfader curve characteristics.
w ON/OFF (UTILITY) button
— ON/ OFF: Turns the MIDI function on/ off (page 16).
— UTILITY: Displays the [USER SETUP] or [CLUB SETUP] screen (page 22).
x START/ STOP button (page 16)
Sends the MIDI start/ MIDI stop signals.
y LFO FORM (WAKE UP) button
— LFO FORM: When [MIDI LFO] is selected at BEAT EFFECT, the MIDI sig-
nal's waveform switches each time the button is pressed (page 19).
— WAKE UP: Cancels the auto standby mode (page 22).
z Main unit display
A X-PAD (page 15)
Adjusts the quantitative parameter of the BEAT EFFECT function.
B BEAT c, d buttons (page 15)
Sets the beat fraction for synchronizing the effect sound.
C TAP (ENTER) button
— TAP: When the BPM measurement mode is set to [TAP], the BPM is input
manually by tapping the button with a finger (page 15).
— ENTER: Used to change this unit's settings (page 22).
D QUANTIZE button
! Used to change this unit's settings (page 22).
! When the QUANTIZE function is turned on for BEAT EFFECT, the effect is
applied to the sound without going off tempo when the currently playing
track. (page 15).
E AUTO/TAP button (page 15)
Switches the BPM measurement mode.
12
En
) selector switch (page 13)
, ) selector switch (page 13)
F DELAY, ECHO, SPIRAL, REVERB, TRANS, FILTER, FLANGER,
PHASER, ROBOT, MELODIC, SLIP ROLL, ROLL, REV ROLL, SND/RTN
(MIDI LFO) selector switch (page 15)
Switches the BEAT EFFECT effect type.
G 1, 2, 3, 4, MIC, CF.A, CF.B, MASTER selector switch (page 15)
Switches the channel to which the BEAT EFFECT is to be applied.
H TIME control (page 15)
Adjust the BEAT EFFECT's time parameter.
I LEVEL/ DEPTH control (page 15)
Adjusts the BEAT EFFECT's quantitative parameter.
J ON/ OFF button (page 15)
Turns the BEAT EFFECT function on/ off.
Do not pull on the channel fader and crossfader knobs with excessive force. The
knobs are not designed to be removed. Pulling the knobs strongly may result in
damaging the unit.