To Install The Engine Compartment Contact; To Install The Emergency-Current Siren; To Install The Led; To Install The Ultrasonic Module - BMW E46 Einbauanleitung

5. To install the engine compartment
contact
F 46 82 036 R
Fit the engine compartment contact (1) into the
recess in the external jump starting support (3)
provided for it.
Connect branch I, plug X161 (2) to the engine
compartment contact (1).
6. To install the emergency-current
siren
Cars from the start of the Series to 3/99 only
F 46 82 037 R
Mark dimensions A and B on the holder (2) as
shown. Centrepunch the marked point and drill
through it using a 5.5 mm drill bit.
Dimensions: A = 26 mm
B = 30 mm
Deburr drilled holes and treat them with the
anti-corrosive prescribed by BMW. Remove all drill
chippings.
Bolt the emergency-current siren (1) to the holder (2)
using the hexagonal nut, size M6 (3).
F 46 0003 R
Hold the emergency-current siren (1) and the holder
on the car next to the heater/air conditioning unit (2).
Mark the hole on the car, centrepunch the marked
point (3) and drill through it using a 3.5 mm drill bit.
Deburr drilled holes and treat them with the
anti-corrosive prescribed by BMW. Remove all drill
chippings.
F 46 0004 R
Secure the holder for the emergency-current siren (1)
using the enclosed hexagonal self-tapping screw (2).
Connect branch G, plug X372 (3) to the emergency-
current siren (1).
Cars after 4/99 only
F 46 0021 2W
Secure the emergency-current siren (1) to the holder
(2) using the hexagonal nut, size M6 (3).
F 46 0043 2W
Insert the Prestol cage (1) into the square hole on the
car as shown.
F 46 0042 2W
Secure the emergency-current siren (1) to the Prestol
cage using the enclosed hexagonal screw, size M6
20
(2). Connect branch G, plug X372 (3) to the
emergency-current siren (4).

7 . To install the LED

Cars from the start of the Series up to and
including 8/99 with a free slot in the switch strip
only
F 46 82 048 R
Lay the black 4-pin plug X514 (1) to a free slot in
H
the switch strip on the centre console. Connect
branch H (1) to the LED (2). Fit the LED (2) in the
switch strip. Cut the switch trim to suit the car's
equipment and refit it.
The LED for installation in the switch strip is not
supplied in the installation kit (see ordering
instructions on page 2).
Cars without a free slot in the switch strip and
cars from 9/99 with a switch centre only
F 46 0044 2W
Mark dimensions A and B on the centre console (1)
as shown. Centrepunch the marked position and
carefully drill and deburr a hole with a 8.0 mm drill bit.
Dimensions: A = 83 mm
B = 23 mm
F 46 0045 2W
Insert the LED (1), if necessary slightly enlarge the
hole.
Connect the LED (1) cables, red/black cable to pin 1
of the enclosed 4-pin black plug casing. Connect the
grey/black/yellow cable to pin 4 of the 4-pin black
plug casing.
Lay branch H, black 4-pin plug X514 to the centre
console.
Connect branch H to the connector for the LED (1).

8. To install the ultrasonic module

Cars without a slide/tilt sunroof only
F 46 82 041 R
When affixing the template (1), it must be
ensured that the template (1) is affixed in the
centre.
Affix the template (1) as shown in the centre of the
head liner (2). Cut out the section with a sharp carpet
knife.
Cars with a slide/tilt sunroof only
F 46 82 042 R