Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach 4903303924 Originalbetriebsanleitung

DE GB

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
that you read through the entire operating instruc-
tions before putting the machine into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications. The operating instructions contain impor-
tant notes on how you work with the machine safely,
expertly, and economically, and how you can avoid
hazards, save repair costs, reduce downtime and in-
crease the reliability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed con-
scientiously. Only persons who have been trained in
the use of the machine and have been informed of
the various dangers may work with the machine. The
required minimum age must be observed. In addition
to the safety requirements in these operating instruc-
tions and your country's applicable regulations, you
should observe the generally recognized technical
rules concerning the operation of identically con-
structed devices.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
FR CZ SK DK ES FIN IT NL PL PT
2. Device description (Fig. 1-3)
1 Safety glass
2 Spark deflector
3 Spark deflector adjusting screw
4 Fastening screw Safety glass holder
5 Guard hood
6 Grinding wheel
7 Workpiece support star screw
8 Workpiece support
9 Grinding / sanding belt
10 Belt guidance adjustment screw
11 Clamp screw for the top belt roller
12 Fastening screw for side cover
13 Side cover
14 Mounting point
15 Foot
16 On/Off switch
17 Coolant reservoir
18 Fastening screw for workpiece support

3. Scope of delivery

Grinder/Sander (1)
Instruction manual (1)
Sanding disc (1)
Sanding belt (1)
Grinding wheel dresser (1)
Waranty sticker (1)
• Open the packaging and remove the device
carefully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warran-
ty period has expired.
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

The grinder/sander is a combination device for the
coarse and fine grinding/sanding of metals, woods
of all kinds and other materials using the appropriate
grinding/sanding wheel or belt.
The machine may only be used with grinding/san-
ding wheels or belts which are suitable for it and
comply with the characteristic data in these instruc-
tions.
The machine is allowed to be used only for its
intended purpose! Even when the equipment is used
as prescribed it is still impossible to eliminate certain
residual risk factors. The following hazards may
arise in connection with the machine's construction
and layout:
• Contact with the grinding wheel where it is not
covered.
SE SI NO
17 / 136