Inhaltsverzeichnis
Werbung
12. Note:
Depending on the kind of vehicle, the function of 3* and 5* may
be different. In this case, be sure to connect 2* to 5* and 4* to 3*.
1*
1. This product
3*
2*
2. Rear output or
subwoofer output
5*
4*
3. Antenna jack
4. Front output
13. Connect leads of the same
5. Fuse (10 A)
color to each other.
14. Cap (1*)
Do not remove cap if this
terminal is not in use.
15. Yellow (3*)
16. Yellow (2*)
Back-up
Connect to the constant
(or accessory)
12 V supply terminal.
17. Red (5*)
18. Red (4*)
Accessory
Connect to terminal controlled
(or back-up)
by ignition switch (12 V DC).
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
34. Yellow/black
20. ISO connector
Note:
If you use an equipment with Mute
function, wire this lead to the Audio Mute
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to
lead on that equipment. If not, keep the
connect to both connectors.
Audio Mute lead free of any connections.
35. Notes:
• Change the initial setting of this unit (refer to the Operation
Manual). The subwoofer output of this unit is monaural.
• When using a subwoofer of 70 W (2 Ω) , be sure to connect
with Violet and Violet/black leads of this unit. Do not connect
anything with Green and Green/black leads.
22. Connect with RCA cables
(sold separately)
9. AUX jack (3.5 ø)
11. Wired remote input
Hard-wired remote control
10. Note:
adaptor can be connected
Use a stereo mini plug cable
(sold separately).
to connect with auxiliary
equipment.
6. IP-BUS input (Blue)
8. Multi-CD player
7. IP-BUS cable
(sold separately)
24. Blue/white
Connect to system control terminal of the
power amp (max. 300 mA 12 V DC).
25. System remote control
26. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
27. Blue/white (6*)
28. Note:
+
The pin position of the ISO connector will differ
29. Front speaker
depends on the type of vehicle. Connect 6* and 7*
≠
when Pin 5 is an antenna control type. In another
30. Left
type of vehicle, never connect 6* and 7*.
+
21. Speaker leads
32. Rear speaker or
Front left +
White:
subwoofer
≠
White/black: Front left ≠
Front right +
Gray:
Gray/black: Front right ≠
33. Perform these connections when
Green:
Rear left + or subwoofer +
using the optional amplifier.
Green/black: Rear left ≠ or subwoofer ≠
Rear right + or subwoofer +
Violet:
Violet/black: Rear right ≠ or subwoofer ≠
Connecting the Units
Note:
•
When this unit is installed in a vehicle without
23. Power amp
ACC (accessory) position on the ignition switch,
(sold separately)
red cable must be wired to the terminal that can
detect the operation of the ignition key.
Otherwise, battery drain may result.
23. Power amp
(sold separately)
ACC position
No ACC position
•
Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
•
To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the bat-
tery before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhe-
sive tape around them where they lie against
metal parts.
— Place all cables away from moving parts,
such as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
+
— Do not pass the yellow cable through a hole
29. Front speaker
into the engine compartment to connect to a
≠
battery.
31. Right
— Cover any disconnected cable connectors
with insulating tape.
— Do not shorten any cables.
+
32. Rear speaker or
— Never cut the insulation of the power cable of
this unit in order to share the power to other
subwoofer
≠
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.
•
Control signal is output through blue/white cable
Connection Diagram
when this unit is powered on. Connect it to an
external power amp's system remote control or
1. This product
the vehicle's auto-antenna relay control terminal
2. Rear output or subwoofer output
(max. 300 mA, 12 V DC). If the vehicle is
3. Antenna jack
equipped with a glass antenna, connect it to the
4. Front output
antenna booster power supply terminal.
5. Fuse (10 A)
•
Never connect blue/white cable to external power
6. IP-BUS input (Blue)
amp's power terminal. Also, never connect it to
7. IP-BUS cable
the power terminal of the auto antenna.
Otherwise, battery drain or malfunction may
8. Multi-CD player (sold separately)
result.
9. AUX jack (3.5 ø)
•
IP-BUS connectors are color-coded. Be sure to
10. Note:
connect connectors of the same color.
Use a stereo mini plug cable to connect with
auxiliary equipment.
•
Black cable is ground. This cable and other prod-
uct's ground cable (especially, high-current prod-
11. Wired remote input
ucts such as power amp) must be wired separate-
Hard-wired remote control adaptor can be con-
ly. Otherwise, fire or malfunction may result if
nected (sold separately).
they are accidentally detached.
12. Note:
Depending on the kind of vehicle, the function of
•
Cord function may differ according to the
3* and 5* may be different. In this case, be sure
product, even if cord color is the same. When
to connect 2* to 5* and 4* to 3*.
connecting this system, be sure to check all
13. Connect leads of the same color to each other.
manuals and connect cords correctly.
14. Cap (1*)
Do not remove cap if this terminal is not in use.
15. Yellow (3*)
Back-up (or accessory)
16. Yellow (2*)
Connect to the constant 12 V supply terminal.
17. Red (5*)
Accessory (or back-up)
18. Red (4*)
Connect to terminal controlled by ignition swich
(12 V DC).
19. Black (chassis ground)
Connect to a clean, paint-free metal location.
20. ISO connector
Note:
In some vehicles, the ISO connector may be
divided into two. In this case, be sure to connect
to both connectors.
21. Speaker leads
Front left +
White:
White/black: Front left ≠
Gray:
Front right +
Gray/black: Front right ≠
Rear left + or subwoofer +
Green:
Green/black: Rear left ≠ or subwoofer ≠
Violet:
Rear right + or subwoofer +
Violet/black: Rear right ≠ or subwoofer ≠
ENGLISH
22. Connect with RCA cables (sold separately)
23. Power amp (sold separately)
24. Blue/white
Connect to system control terminal of the power
amp (max. 300 mA 12 V DC).
25. System remote control
26. Blue/white (7*)
Connect to auto-antenna relay control terminal
(max. 300 mA 12 V DC).
27. Blue/white (6*)
28. Note:
The pin position of the ISO connector will differ
depends on the type of vehicle. Connect 6* and
7* when Pin 5 is an antenna control type. In
another type of vehicle, never connect 6* and 7*.
29. Front Speaker
30. Left
31. Right
32. Rear Speaker or subwoofer
33. Perform these connections when using the
optional amplifier.
34. Yellow/black
If you use an equipment with Mute function,
wire this lead to the Audio Mute lead on that
equipment. If not, keep the Audio Mute lead free
of any connections.
35. Notes:
•
Change the initial setting of this unit (refer to the
Operation Manual). The subwoofer output of this
unit is monaural.
When using a subwoofer of 70 W (2 Ω), be sure
•
to connect with Violet and Violet/black leads of
this unit. Do not connect anything with Green
and Green/black leads.
Werbung
Inhaltsverzeichnis
