Know Your Product; Operation - Sparky HeavyDuty GUR 12Li-C HD Originalbetriebsanleitung

spite full charging, the life of the battery may be over.
Replace the battery immediately.
Charging indication:
▪ The green LED light starts to glow upon plugging the
charger in the mains.
▪ The green LED light starts to blink after the battery
has been placed in the charger, thus indicating the
beginning of the charging process.
During the charging process the charger and battery
might become warm. This is a normal condition, and
does not indicate a problem.
▪ The green LED light starts to glow constantly after
completion of charging.
The charger features thermal overload protection for the
battery. Nevertheless we recommend withdrawing the
battery from the charger upon expiring of the charging
time. You may use additionally an electric timer in order
to control the charging time.
State description
Constantly glowing Ready-to-charge state
green light When there is no battery pack in-
serted in the charger, green light
indicates ready-to-charge state.
Blinking green light: Charging
Battery pack is being charged.
Constantly glowing Fully charged battery pack
green light When there is a battery pack in-
serted in the charger, green light
indicates that it is fully charged.
Constantly glowing Battery temperature is out of
the admissible charging tem-
red light
perature range 0÷45
Move the charger with battery to
another premises with appropri-
ate environmental temperature.
Once the temperature reaches the
admissible charging temperature,
the charger automatically switches
to charging mode.
Blinking red light: Fault
In failure mode charging is not pos-
sible. The reason for failure may
be one of the following:
▪ Battery pack is not inserted
▪ Battery pack terminals are
▪ Damaged battery pack;
▪ Unrecognized battery pack.

Know your product

Before using the power tool, familiarize yourself with all
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. Locking sleeve
2. Bit holder
Original instructions
C
o
properly;
dirty;
3. LED work light
4. LED battery indicator
5. ON/OFF trigger switch
6. Forward reverse switch
7. Battery release buttons
8. Battery
9. LED charge state indicator
10. Charger

Operation

FITTING AND REMOVING THE BATTERY PACK
To remove the battery from the machine: press the battery
release buttons (7) and take the battery out of the tool.
WARNING: Always set the forward/reverse
switch (6) in central position before any work on the
machine e. g. fitting and removing a battery, changing
the bit,, transport, maintenance and storage.
To install the battery: Insert the charged battery into the
opening at the base of the power tool until the battery is
securely latched with a click.
BATTERY STATE INDICATION (Fig. 2)
The battery state during operation can be checked on
the LED display (4) by pressing the ON/OFF trigger
switch (5).
Depending on the number of illuminated LEDs the bat-
tery state is as follows:
3 Battery capacity: 60 - 100%
2
Battery capacity: 30 - 60%
1 Battery capacity: < 30%
1 Battery capacity: < 20%. The battery
Blinking light must be recharged.
Problems with battery. The display is
Blinking light activated upon pressing the trigger of
the switch. It may show one of the fol-
lowing battery states:
▪ Low battery ► Battery has to be
recharged;
▪ Temperature
been actuated ► Battery must
be cooled down prior to resuming
operation;
▪ Damaged or unrecognized bat-
tery ► Battery has to be replaced
The direction of decreasing the charge level indicated by
the LEDs is marked on the housing of the power tool.
LED WORK AREA LIGHT
The machine is equipped with LED light (3) to illuminate
the work area and improve visibility when drilling in areas
with insufficient light. To turn the LED light on press the
trigger of switch (5). LED light will automatically turn off 5
seconds after releasing the trigger of switch (5).
Electronic control may turn off the excessively overload-
ed machine in order to protect it. This mode is signalled
by blinking LED work area light (3). The power tool can
protection has
7
EN