Before Starting The Equipment; Assembly - EINHELL TC-TS 2025/1 UA Originalbetriebsanleitung

Operation
L sound pressure level ........................ 91 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 104 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The quoted values are emission values and not
necessarily reliable workplace values. Although
there is a correlation between emission and im-
mission levels it is impossible to draw any certain
conclusions as to the need for additional precau-
tions. Factors with a potential infl uence on the ac-
tual immission level at the workplace include the
duration of impact, the type of room, and other
sources of noise etc., e.g. the number of machi-
nes and other neighboring operations. Reliable
workplace values may also vary from country to
country. With this information the user should at
least be able to make a better assessment of the
dangers and risks involved.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
Anl_TC_TS_2025_1_UA_SPK1.indb 24 Anl_TC_TS_2025_1_UA_SPK1.indb 24
GB

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
•
Unpack the bench-type circular saw and
check it for damage which may have occurred
in transit.
•
The machine has to be set up where it can
stand firmly, e.g. on a work bench, or it must
be bolted to a strong base.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the saw blade to run
freely.
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.

6. Assembly

Danger! Pull out the power plug before carry-
ing out any maintenance, resetting or assem-
bly work on the cutting-off machine!
6.1 Assembling the base frame
(Fig. 4-5)
•
Turn the saw upside down and place it on the
floor.
•
Use the hex screws (a) to fasten the four legs
(29) loosely to the saw.
•
Now use the round-head screws (c) and the
nuts (b) to fasten the longitudinal struts (31)
and the cross-struts (30) loosely to the legs.
Important: The longer struts have to be used
on the sides.
•
Finally, tighten all screws and nuts on the
base frame.
•
Screw the additional legs (36) to the rear legs
(29) so that they point towards the rear of the
machine (Fig. 5).
•
Plug the rubber feet (13) onto the legs (29).
- 24 -
20.06.16 15:10 20.06.16 15:10