Electrical Safety - Black & Decker KS2005E Handbuch

When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
: The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-on button
3. Variable speed control knob
4. Mode selector switch
5. Saw blade locking lever
6. Saw blade holder
7. Shoe plate
8. Shoe plate locking knob
9. Scroll knob
10. Saw blade storage compartment
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the saw blade (fig. A)
Hold the saw blade (11) as shown, with the teeth facing
u
forward.
Push the lever (5) downwards.
u
Insert the shank of the saw blade into the blade holder (6)
u
as far as it will go.
Release the lever.
u
Adjust the blade support roller as described below.
u
Adjusting the blade support roller (fig. A & B)
After fitting the blade, you need to adjust the blade support
roller (12).
Turn the blade support adjustment screw (13) in the
u
counterclockwise direction.
Slide the blade support roller against the rear of the blade.
u
The blade must locate in the central recess of the roller.
Turn the blade support adjustment screw in the clockwise
u
direction to lock the blade support in place.
Connecting a vacuum cleaner to the tool (fig. C & D)
Align the dust extraction adaptor (14) with the saw shoe
u
as shown.
Insert the ribs (15) into the slots (16).
u
Push the adaptor backwards to lock it in position.
u
Connect the vacuum cleaner hose (17) (not supplied) to
u
the adaptor.
Dust extraction is not possible when making bevel cuts.
Warning! Do not use the dust extraction adaptor when sawing
metal.
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Never use the tool when the saw shoe is loose or
removed.
Adjusting the shoe plate for bevel cuts (fig. E)
The shoe plate can be set to a left or right bevel angle of up to
45°.
Turn the locking knob (8) in direction A to release the shoe
u
plate (7).
Pull the shoe plate (7) backwards and set it to the required
u
angle. You can use the scale or a protractor to check the
angle.
Turn the locking knob (8) in direction B to lock the shoe
u
plate in place.
To reset the shoe plate for straight cuts:
Turn the locking knob (8) in direction A to release the shoe
u
plate (7).
Pull the shoe plate backwards and set it to an angle of
u
approx. 0°.
Push the shoe plate forward.
u
Turn the locking knob (8) in direction B to lock the shoe
u
plate in place. Make sure that the shoe plate is supported
by the guide ribs.
Setting the operating mode (fig. F)
In the straight cutting mode, the saw blade can be set and
locked in 4 positions: forward, reverse, left or right.
Turn the mode selector switch (4) to position A
u
(scrolling mode).
Rotate the saw blade into the required direction using the
u
scroll knob (9).
ENGLISH
7