Tool Holder, Attachments; Angle Attachment - Protool QuaDrive PDC 12-4 TEC Originalbetriebsanleitung

6.5 Impact drilling
► The machine was designed for impact drilling into
tiles, brickwork and stone.
Set the switch [1-4] to "hammer" symbol. Turn the
wheel [1-6] into the drill position.
7

Tool holder, attachments

7.1 Chuck
The chuck is used for clamping drill and screw-
driver bits.
Attaching the chuck
► Before first use, the spindle [4-1] should
be painted with a thin layer of multipurpose
grease.
Attach the chuck to the drill spindle [4-1].
Pull the release ring [4-2] forwards.
Turn until the hexagon pinon the chuck engages in
the hexagon socket holder in the drill spindle.
Push the chuck all the way onto the drill spindle.
Release the ring [4-2].
Detaching the chuck
Pull the release ring [4-2] forwards.
Remove the chuck.
Changing tools
Turn the clamping sleeve [4-3] anticlockwise to
open the clamping jaws.
The arrow on the chuck shows the direction to turn
to open it.
Insert the tool into the chuck.
CAUTION
Risk of injury
► Clamp the tool centrally in the chuck!
Turn the clamping sleeve [4-3] clockwise to clamp
the tool.
7.2 Tool chuck CENTROTEC
The tool chuck CENTRO TEC allows you to change
tools with a CENTRO TEC shank in a matter of sec-
onds.
► Always use a CENTROTEC tool chuck to clamp
CENTROTEC tools.
CAUTION
Risk of cutting injuries when changing the
tool!
► Wear protective gloves!
Attaching the CENTROTEC
Pull the release ring [5-1] forwards.
Attach the tool chuck to the drill spindle [4-1].
Release the ring [5-1].
Detaching the CENTROTEC
Pull the release ring [5-1] forwards.
Remove the tool chuck.
Changing tools
To fi t or remove a tool with a CENTRO TEC shank,
pull back the orange ring [5-2].
When attaching the tool, rotate until the hexagon
shank engages in the hexagon holder on the drill
spindle.
Release the ring [5-2].
7.3

Angle attachment

► Not for impact drilling, but just for normal work!
The angle attachment allows you to work (drill,
fasten) vertically in relation to the longitudinal axis
on the machine.
Fitting the angle attachment
► Before fi rst use, the spindle [4-1] and gearbox
neck [6-1] should be painted with a thin layer
of multipurpose grease.
Release the lever of the angle attachment.
Fit the attachment right down onto the neck of the
gearbox so that the recess in the attachment sits
on the protruding part of the gearbox.
Secure the attachment lever.
The angle attachment can be positioned through
30°.
Attaching/Detaching the chuck
The chuck is secured to the shaft of the angle at-
tachment and the drill spindle on the machine in
the same way.
7.4 Depth stop DC UNI FF
The depth stop allows you to insert a screw to a
defi ned depth. You can set the dimension to which
the screw head is to project over the workpiece, or
to which it is to be countersunk in the workpiece.
Assembly
Place the depth stop onto the spindle of the screw-
driver [8-1].
Pull the release ring [8-2] forwards.
Turn it until the hexagonal pin of the stop engages
in the internal hexagon support of the machine.
Press to stop onto the machine spindle. Let go of
the release ring.
Disassembly
Pull the release ring [8-2] forwards and then re-
move the depth stop from the spindle.
Tool change
Take sleeve A or B off the depth stop. Insert the
corresponding bit or plug-in bit adapter in the mag-
netic holder [8-3]. Refi t sleeve A or B.
Setting the depth
Set the desired screw-in
depth by turning the hous-
ing [8-4] – see symbol on
the holder. Each notch
15