Audio Settings - Pioneer DEH-X5900BT Bedienungsanleitung

AUDIO settings

Menu Item
EQ SETTING
[SUPER BASS], [POWERFUL],
[NATURAL], [VOCAL], [CUSTOM1],
[CUSTOM2], [FLAT]
Select an equalizer band and
level for further customising.
Equalizer band: [50HZ] to
[12.5kHZ]
Equalizer level: [–6] to [+6]
FADER*1 (Only for standard mode)
BALANCE
SUBWOOFER
[ON], [OFF]
SUBWOOFER*2
[NOR], [REV]
SPEAKER LEVEL
Network mode: [HIGH L], [HIGH
R], [MID L], [MID R], [SUBWOOFER]
Standard mode: [FRONT L],
[FRONT R], [REAR L], [REAR R],
[SUBWOOFER]
Output level: [–24] to [10]
CROSSOVER
POSITION
[OFF], [FRONT LEFT] (front seat
left), [FRONT RIGHT] (front seat
right), [FRONT] (front seats), [ALL]*
* Only for standard mode
Description
Select or customise the equalizer curve.
• When you select a setting other than
[CUSTOM1] and [CUSTOM2], you can also
customise the equalizer curve by pressing and
holding the M.C. dial, then store the
customised equalizer curve in [CUSTOM1].
Adjust the front and rear speaker balance.
Adjust the left and right speaker balance.
Set to [ON] when using a subwoofer speaker.
Select the subwoofer phase.
Select a speaker unit (filter) and adjust the
output level.
• Each value you have adjusted changes when
you change the [POSITION] setting (page 15).
Select a speaker unit (filter) to adjust the HPF or
LPF cut-off frequency and the slope for each
speaker unit.
For details on the [CROSSOVER] setting, see
page 13.
Select a listening position to adjust the speakers'
output levels automatically and add a delay time
that corresponds to the number and locations of
occupied seats.
Menu Item
TIME ALGNMNT
[INITIAL], [OFF], [CUSTOM]
Select a type of speaker and
adjust the speaker distance for
further customising in [CUSTOM].
Network mode: [HIGH L], [HIGH
R], [MID L], [MID R], [SUBWOOFER]
Standard mode: [FRONT L],
[FRONT R], [REAR L], [REAR R],
[SUBWOOFER]
Speaker distance (cm): [350] to
[0.0]
SAVE SETTINGS
[YES], [CANCEL]
LOAD SETTINGS
BASS BOOST
[0] to [+6]
LOUDNESS
[OFF], [LOW], [MID], [HI]
AUTO LV CTRL
[OFF], [MODE1], [MODE2]
SLA
[+4] to [–4]
*1 Not available when [SW] is selected in [REAR-SP] in the INITIAL settings (page 5).
*2 Not available when [FUL] is selected in [REAR-SP] in the INITIAL settings (page 5).
Description
Select or customise the time alignment settings
to reflect the distance between the listener's
position and each speaker.
• Select [INITIAL] to initialize the setting value.
• Select [OFF] to reset all setting values to 0.
• The [CUSTOM] setting is available when
[FRONT LEFT] or [FRONT RIGHT] is selected in
[POSITION] (page 15).
• The [CUSTOM] setting is not available when
[OFF] is selected in [SUBWOOFER] (page 15).
Save to later recall the following sound settings
at their current values: [CROSSOVER], [SPEAKER
LEVEL], [EQ SETTING], [POSITION], [TIME
ALGNMNT], [BASS BOOST], [SUBWOOFER].
Load the sound settings, when you have already
performed [SAVE SETTINGS].
Select the bass boost level.
Compensate for clear sound at low volume.
Adjust the difference in volume levels among
sources or audio files automatically.
Adjust the volume level for each source except
FM.
Each of the below combinations are set to the
same setting automatically.
• When making a USB connection, set USB, iPod,
ANDROID, SPOTIFY, and APP.
• When making a Bluetooth connection, set BT
AUDIO, iPod, ANDROID, SPOTIFY, and APP.
15
En