Kenwood KM070-Serie Anleitung Seite 12

display
For your safety the mixer is fitted with 5 separate safety sensors which will operate when using the mixer in the
cooking mode. If the mixer is switched on and a safety sensor activated, the timer/temperature display will show
an error message e.g. 'E:01'. This will be accompanied by a beeping sound and the mixer will not work. Check
the following error messages:-
Error Message
The head of the machine is in the raised position. Close the head. Turn the speed control
When the head is lifted, a safety sensor disables
the motor and heater. If the speed control is
E:01
turned to any setting other than the Off 'O'
position when the head is raised, this message
is displayed and the motor will not switch on.
The Cooking Chef Bowl is not fitted. The heating Ensure that the Cooking Chef bowl is
function will only work if the Cooking bowl is
E:02
being used. This bowl must also be correctly
fitted. Safety sensors will detect an incorrect
bowl or the correct bowl incorrectly fitted.
The heat shield is not fitted. The heating function Ensure the heat shield is fitted
E:03
will be disabled if the heat shield is not correctly
fitted.
The slow speed outlet and high speed/medium
speed outlet covers are not fitted. These covers
are fitted with safety sensors. If the covers are
E:04
not fitted correctly the heating will switch off and
if stir functions are selected, the motor will run
continuously. Mixing speeds min to max will
run continuously.
Temperature sensor problem. If the heater
control detects a bowl temperature higher than
E:09
expected during normal use, the motor and
heater will automatically switch off.
Motor speed or overheat problem. If the motor
stalls or gets too hot, the control system will
E:10
automatically switch off the motor and heater.
If these or any other error codes continue to appear on the display contact Kenwood Customer Care.
to use the countdown timer
The timer can be used in both the cooking and non cooking modes. If a countdown time is not selected, the
timer will automatically count up in 1 second intervals whilst the mixer is in operation. The maximum running time
is 3 hours.
1 Connect the mixer to the power supply. The display will briefly show
indicator visible .
2 Press either the + or – button and 0:00 will appear in the display.
3 Press either the + or – button until the desired time is displayed. The timer will count up in 5 second intervals. If
the button is pressed continuously the numbers will change more quickly the longer it is held down. A maximum
time of 3 hours can be set.
Note: If the + button is pressed when the timer is at 3:00 the displayed time will change to 0:00. If the – button is
pressed when the timer is at 0:00 the displayed time will change to 3:00.
4 Turn the speed control to the desired speed, the mixer will start and the timer will count down in 1 second
intervals.
The mixer operation can be paused at any time by turning the speed control to the off 'O' position. This will also
G
pause the timer. The timer will continue to count down when the mixer is re-started.
5 The mixing process will automatically stop when the total time has elapsed and audible beeps will be emitted for
3 seconds. The display will flash for 5 seconds and then clear showing the power on indicator
to reset the timer
1 Zero the timer by pressing the + and – buttons at the same time (the speed control must be in the off 'O' position).
If the machine has been idle for 10 minutes, the LCD display and backlight will enter 'sleep mode' and all the
G
displays will turn off. If any button or control knob is activated, the display will resume its previous format.
12
Description Solution
to the 'O' position and then select the
desired speed.
being used. Check that the bowl
is fitted correctly. Turn the speed
control to "0" and then select desired
speed.
correctly. Turn the speed control to 'O'
and then select desired speed.
Ensure that all covers are fitted correctly.
Turn the speed control to 'O' and then
select desired speed.
Turn the speed control to 'O', unplug the
machine and allow to cool. Check
that the bowl base and temperature
sensors are clean. Replace plug and
switch on as normal.
Turn the speed control to 'O' and unplug
the machine. Remove any obstructions
causing the motor to stall. Ensure all
the air vents are clear of obstructions.
Plug in and switch on.
and then clear leaving the power on
.