EINHELL GC-EM 1536 Betriebsanleitung Seite 24

Fitting the wheels (Fig. 3a and b)
Take a rear wheel (Fig. 2/Item 11) and push it
onto the axle as shown in Fig. 3a. Then slide a
washer (Fig. 2/Item 15) onto the axle and fasten
all parts with the supplied split pin (Fig. 2/Item 14)
as shown in Fig. 3a. Finally, press the wheel cap
(Fig. 2/Item 12) onto the wheel as shown in Fig.
3b. Proceed in exactly the same way on the other
side.
Mounting the push bar (Fig. 4 to 7).
Mount a bottom push bar (Fig. 2/Item 2) onto the
screw provided for it and secure everything with
a wing nut (Fig. 2/Item 13) as shown in Fig. 4.
Proceed in the same way on the other side. When
you fi t the top push bar you can decide the height
of the push bar by selecting the appropriate fas-
tening hole (Fig. 5). Finally, secure the top push
bar to the bottom push bar as shown in Fig. 6.
Now you can attach the motor cable to the push
bar (Fig. 7/Item A) using the cable clips (Fig. 2/
Item 16).
Mounting the grass basket
(see Figs. 8a and b)
Press the grass box handle (Fig. 8a/Item 21)
into the grass basket as shown in Fig. 8a. Before
you fi t the grass basket you must ensure that the
motor is switched off and the blade is not rotating.
Lift the ejector fl ap (Fig. 8b/Item 3) with one hand.
With the other hand, hold the grass basket by the
handle and hook it in from above (Fig. 8b).
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling level
indicator (Fig. 2/Item 18) which is opened by the
airfl ow that the lawn mower generates during ope-
ration. If the fl ap closes during mowing, the grass
collecting device is full and must be emptied. To
ensure the proper functioning of the fi lling level
indicator, the holes under the fl ap must always be
kept clean and passable.
Adjusting the cutting height
Important!
Adjust the cutting height only when the motor is
switched off and the power cable has been dis-
connected.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
power plug.
Anl_GC_EM_1536_SPK7.indb 24 Anl_GC_EM_1536_SPK7.indb 24
GB
The cutting height is adjusted as follows
(see Fig. 9):
1. Push the lever inwards.
2. Set the lever to the desired cutting height.
3. Release the lever and check that it is securely
seated in the lock.
Reading off the cutting height
The cutting height can be set between 25-66 mm
in 5 intervals, and can be read off on the scale.
Power supply
The lawn mower can be connected to any light
socket-outlet with a 220-240 Volt alternating
current. However, the socket outlet must have an
earthing contact protected by a 16 A circuit brea-
ker. Additionally, a residual current device (RCD)
circuit-breaker with max. 30 mA must be used!
Power cable for the device
Please only use power cables that are not dama-
ged. The total length of the power cable should
not exceed 50 meters; going beyond this distance
will reduce the power output of the electric motor.
The power cable must have a cross-section of 3
x 1.5 mm. The insulating sheath of lawn aerator
power cables is frequently damaged.
Some of the causes for this are:
•
Cuts caused by driving over the cable.
•
Pinching when the power cable is dragged
under doors and pulled through windows.
•
Cracking due to old age of the insulation.
•
Kinking by improperly fastening or guiding the
power cable.
The power cables must, at the very minimum, be
of type HO5RN-F and 3-stranded. The cable type
must be printed somewhere on the power cable.
Only purchase power cables that are marked!
Plugs and socket couplers for the power cables
must be made from rubber and splash-proof.
There is a limit to how long power cables can be.
Longer power cables require larger conductor
cross-sections. Power cables and connecting li-
nes must be regularly checked for damage. Ensu-
re that the lines are switched off before checking
them. Completely unwind the power cable. Also
check power cable entry points, plugs and socket
couplers for kinks.
- 24 -
15.07.14 12:58 15.07.14 12:58