Field Of Application; Before You Begin - WAGNER ProjectPro 119 Originalbetriebsanleitung

Field of application

Coating of interior walls as well as small and medium-sized objects
outdoors (e.g. garden fences, garage doors, etc.).
Assembly
Figure 2 - Unfolding the Cart
1. Lift the basic unit using the container holder. Pull the foot lock
up and fold the feet out.
2. Move foot lock down to lock into place.
3. Twist the knob on either side of the cart toward the "UP"
arrow until it stops. Lift the handle until the motor housing
and handle locks into place. Be careful not to pinch the power
cord with the cart.
Figure 3 - Attaching the Hose
Make sure that the pump is switched off (position O) and
the spray device is disconnected from the power supply.
Danger
1. Thread the high pressure hose to the spray hose port. Tighten
with an adjustable wrench.
2. Thread the other end of the hose to the spray gun. Grip the
spray gun with an adjustable wrench on the handle, and
tighten the hose nut with the other.
i
The spray tip should not be attached until after the
sprayer and spray hose have been purged and primed.
Figure 4 - Attaching the Suction Set
1. Remove cap from inlet valve (a). Thread the suction tube onto
the inlet valve and tighten firmly by hand. Be sure that the
threads are straight so that the fitting turns freely.
2. Push the return hose into the return connection piece.

Before You Begin

Preparation of the Coating Material
Using Project Pro 119 interior wall paints, varnishes and glazes can
be applied by spraying without diluting them, or by diluting them
slightly.
Detailed information is available in the technical data sheet of the
manufacturer ( Internet download).
1. Stir the material thoroughly and dilute it in the container as
per the recommended dilution (an agitator is recommended
for stirring).
Thinning recommendation
Sprayed material
Glazes
Wood preservatives containing
solvents or based on water, mordants,
oils, disinfection agents, plant
protective agents
Paints containing solvents and
water-soluble paints, primers, vehicle
coating paints, thick-film glazes
Interior wall paint (dispersions and latex
paint)
2. Do a test spray (e.g. on to a piece of cardboard).
Figure 5 - Locking the Spray Gun
Figure 6 - Pressure Relief Procedure
Priming
Figure 7 - Preparing to Prime
Figure 8 - Priming the Sprayer
undiluted
undiluted
Figure 9 - Priming the Spray Hose
dilute by 5 - 10%
dilute by 0 - 10%
16
WAGNER Project Pro 119 - 0418C
If the paint sprays evenly, as shown in fig. 12 A, all the
i
setting must be correct.
If the paint looks stripy after spraying, as shown in fig.
12 B, gradually increase the pressure, or dilute more in
5% steps.
Always lock the trigger off when attaching the spray
tip or when the spray gun is not in use.
Danger
1. The gun is secured when the trigger lock is at a 90° angle
(perpendicular) to the trigger in either direction.
Be sure to follow the Pressure Relief Procedure
when shutting the unit off for any purpose. This
procedure is used to relieve pressure from the spray
hose.
Danger
1. Lock the spray gun off. Flip the ON/OFF switch to the OFF
position.
2. Turn the PRIME/SPRAY knob to PRIME.
3. Unlock the spray gun and trigger spray gun into the side of
the material bucket. Lock the spray gun.
1. Spray a little oil out of the provided flask into the marked
opening (tip: tilt the device back). Light household oil can be
substituted if necessary.
i
The PP119 has the Sureflo™ valve that will activate
automatically when the pump is turned ON (l).
1. Place a full container of spraying material underneath the
suction tube (a). Secure the return tube (b) into a waste
container.
2. Slide the PressureTrac™ to maximum pressure (+).
3. Turn the PRIME/SPRAY knob to PRIME.
4. Plug in the sprayer and move the ON/OFF switch to the ON (l)
position.
The unit will begin to draw material up the suction
i
tube, into the pump, and out the return tube. Let the
unit cycle long enough to remove test fluid from the
pump, or until spray material is coming from the return
tube.
5. Switch the pump OFF (O). Remove the return tube from the
waste container and place it in its operating position above
the container of spraying material. Use the metal clip to bind
the two hoses together.
1. Unlock the spray gun and turn the PRIME/SPRAY knob to
PRIME.
i
The spray tip should not be attached to your spray gun
when purging your spray hose.