Additional Safety And Working Instructions - Bosch PSR 10,8 LI-2 Originalbetriebsanleitung

OBJ_BUCH-1196-003.book Page 9 Tuesday, January 8, 2013 4:27 PM
ry and fasteners contacting a "live" wire may make ex-
posed metal parts of the power tool "live" and could give
the operator an electric shock.
 Use appropriate detectors to determine if utility lines
are hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age.
 Switch off the power tool immediately when the tool in-
sert jams. Be prepared for high reaction torque that
can cause kickback. The tool insert jams when:
— the power tool is subject to overload or
— it becomes wedged in the workpiece.
 Hold the machine with a firm grip. High reaction torque
can briefly occur while driving in and loosening screws.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Do not open the battery. Danger of short-circuiting.
Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
 In case of damage and improper use of the battery, va-
pours may be emitted. Ventilate the area and seek
medical help in case of complaints. The vapours can irri-
tate the respiratory system.
 Use the battery only in conjunction with your Bosch
power tool. This measure alone protects the battery
against dangerous overload.
 Use only original Bosch batteries with the voltage list-
ed on the nameplate of your power tool. When using oth-
er batteries, e.g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Symbols
The following symbols are important for reading and understanding the operating instructions. Please take note of the symbols
and their meaning. The correct interpretation of the symbols will help you to use the machine in a better and safer manner.
Symbol Meaning
PSR 10,8 LI-2: Cordless Drill/Driver
Grey-marked area: Handle (insulated
gripping surface)
Read all safety warnings and all instruc-
tions
Bosch Power Tools
Additional Safety and Working In-
structions
 Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health and cause allergic reactions, lead to res-
piratory infections and/or cancer. Materials containing
asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
 Before any work on the machine (e. g., maintenance,
tool change, etc.) as well as during transport and stor-
age, set the rotational direction switch to the centre
position. Unintentional actuation of the On/Off switch can
lead to injuries.
 The battery is supplied partially charged. To ensure full
battery capacity, completely charge the battery in the
battery charger before using for the first time.
 Read the operating instructions of the battery charger.
 Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
 Adjust the gear switch only when the machine is at a
complete stop.
 If the gear switch cannot be pushed to the stop, turn
the drill chuck a little.
 To save energy, only switch the power tool on when using
it.
 The battery charge-control indicator indicates the
charge condition of the battery for a few seconds when
the On/Off switch is pressed half or fully through. It
consists of a three-colour illuminating LED.
LED
Continuous lighting, green
Continuous lighting, orange
Continuous lighting, red
Flashing light, red
Symbol Meaning
Article number
Before any work on the machine itself, re-
move the battery
English | 9
Capacity
≥ 66%
33—66%
11—33%
≤ 11%
2 609 006 873 | (8.1.13)