Denon AVR-2802 Bedienungsanleitung Seite 22

ENGLISH
After starting playback
[1] Adjusting the sound quality (TONE)
The tone control function will not work in the Direct mode.
1
The tone switches as follows each time the
TONE CONTROL button is pressed.
TONE
CONTROL
BASS TREBLE
(Main unit)
2
With the name of the volume to
be adjusted selected, turn the
SELECT knob to adjust the level.
• To increase the bass or treble: Turn the control
clockwise. (The bass or treble sound can be
increased to up to +12 dB in steps of 2 dB.)
• To decrease the bass or treble: Turn the
control counterclockwise. (The bass or treble
sound can be decreased to up to –12 dB in
steps of 2 dB.)
[2] Listening over headphones
1
Connect the headphones to
the PHONES jack of the front
panel.
2
Press the SPEAKER A or B to turn the speaker
off.
(Main unit)
• The output to the speaker and pre-out jacks is
turned off and no sound is produced from the
speakers.
[3] Turning the sound off temporarily (MUTING)
1
Use this to turn off the audio
output temporarily.
Press the MUTING button.
Cancelling MUTING
(Remote control unit)
mode.
Press the MUTING button again.
22
B
REMOTE SIGNAL
SENSOR
LOCK DIGITAL
STAND BY INPUT
AUTO DIGITAL PCM
3
SELECT
(Main unit)
3
If you do not want the bass and treble to be
adjusted, turn on the tone defeat mode.
TONE DEFEAT
The signals do not pass
through the bass and treble
adjustment circuits, providing
higher quality sound.
(Main unit)
PHONES
B
REMOTE SIGNAL
SENSOR
LOCK DIGITAL
INPUT
STAND BY AUTO DIGITAL PCM
1
1 2
NOTE:
To prevent hearing loss, do not raise the volume level
excessively when using headphones.
MUTING
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
AUDIO CD MULTI MUTING
AVR/AVC VIDEO DVD TV
VDP VCR
[4] Combining the currently playing sound with the desired image
1
Simulcast playback
Use this switch to monitor a video source other
than the audio source.
Press the VIDEO SELECT
button repeatedly until the
desired source appears on
VOLUME LEVEL
the display.
Cancelling simulcast playback.
• Select "SOURCE" using the VIDEO
SELECT button.
• Switch the program source to the
2 1
component connected to the video input.
[5] Checking the currently playing program source, etc.
1
On screen display
• Each time an operation is
performed, a description of
that operation appears on
the display connected to the
unit's VIDEO MONITOR OUT
jack.
Also, the unit's operating status can be
checked during playback by pressing the
remote control unit's ON SCREEN button.
Such information as the position of the input
selector and the surround parameter settings
is output in sequence.
Front panel display
• Descriptions of the unit's operations are also
VOLUME LEVEL
displayed on the front panel display.
In addition, the display can be switched to
check the unit's operating status while
playing a source by pressing the STATUS
button.
STATUS
(Main unit)
1
B
REMOTE
SENSOR
STAND BY
VIDEO SELECT
(Main unit)
ON SCREEN
RETURN
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
(Remote control unit) MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP
Using the dimmer function
• Use this to change the brightness of
the display.
The display brightness changes in
four steps (bright, medium, dim and
off) by pressing the remote control
unit's DIMMER button repeatedly.
The brightness changes in 3 steps each time the
button is pressed, and finally the display turns off.
STATUS
DISPLAY
(Remote control unit)
VOLUME LEVEL
SIGNAL
LOCK DIGITAL
INPUT
AUTO DIGITAL PCM
1
VOLUME LEVEL
1
1
1
DIMMER
(Main unit)