Technical Specifications; Instructions For Use Of The Batteries; Operation Of Imatic; Before Operation - Wetrok iMatic XR85 Betriebsanleitung

Technical specifications

iMatic XR85
Nominal voltage:
Theoretical power:
Operating width:
Width of suction nozzle, folded:
Fresh water tank:
Dirty water tank:
Brush motor
Suction turbine
Traction motor
Dosing system
Pump
Overall nominal rating
Battery capacity
Onboard battery charger
Max. charge current
Duration of battery charge
Max. power rating for laser, class 2M

Instructions for use of the batteries

Please observe before operating machine!
Always connect the machine to a mains socket and fully charge the batteries (12 hours charge cycle) after normal use.
If the machine is only used for less than half an hour after fully charging the batteries, do not charge the battery again, until it is reasonably discharged (i.e. after
having used the machine for more than 1 hour). Claims under warranty are voided if this instruction is disregarded. In principle, the warranty period is 1 year.

Operation of iMatic

Before operation:

• Charge the batteries - Connect mains cable with mains plug (see „Machine overview") to a socket outlet (230V). (may take up to 12 hours)
(Setting for gel and wet cell batteries to be carried out directly on charger and by a service technician only.)
• The mains cable must be removed before operation.
• Fill fresh water tank, 105 litres max.
• Connect 5 litre chemicals canister (see „Machine overview").
• Place brush or pad drive disks with pad under the brush housing.
• Adjust seat position by pressing the adjusting lever. Three positions are available.
• Turn on the machine (unlock the emergency stop and turn the key switch).
• Press brush pick-up button (refer to „Touch screen menu navigation").
• Select chemicals canister by turning the dosing lever and restart dosing.
When driving the Wetrok iMatic for the first time, please observe the following instructions:
• The machine is controlled using the steering handles (see „Machine overview"). The steering is controlled electronically, not mechanically.
The steering is similar to that of a bicycle.
• On the control panel (see „Machine overview") press buttons for forward direction and slow mode (turtle symbol).
• Slowly twist the throttle grip backward (see „Machine overview") in order to drive forward with the machine.
Start with small steering handle movements and low driving speeds.
• Twist the throttle grip forward in order to brake the machine.
• Drive the machine for 5 minutes without cleaning – drive in circles, make tight turns, use the brakes and familiarise yourself with
the machine.
• Reversing: Press the reverse direction button on the control panel (see „Machine overview"). Here, too, start slowly and without steering.
A change of direction (forward/backward, backward/forward) causes the freely moveable front wheels to flip, which will lead to a slight
side movement of the machine. Therefore, carry out small steering movements only.
• Select one of the cleaning programmes PGM1, PGM2 or PGM3 (for details refer to „Touch screen menu navigation").
• Set direction of travel to „forward" (refer to „Touch screen menu navigation").
V 24 / 24
m2/h 5100
mm 850
mm 1150
l 105
l 95
W 2 x 500
W 550
W 2 x 550
% 0,2 - 5
W 2 x 25
W 2800
Ah 220/280/320
A 35
h 2-4
mW 5
iMatic XR85
Weight without battery,
without water:
Weight with battery 280 Ah:
Weight: battery+water:
Permissible total weight:
Max. dimensions (LxWxH):
Max. dimensions of battery com-
partment (LxWxH):
Suction turbine
Brush pressure max:
Brush pressure max:
Brush rpm:
Noise level (Leq)
Max. permissible incline
Anti-splash protection:
Certification mark:
Drive speed
Effective acceleration value
28
kg 270
kg 540
kg 655
kg 755
mm 1620 x 750 x 1420
mm 530 x 670 x 430
mbar (m3/h) 180 (90)
N/cm2 0,43
kg 100
1/min. 130
dB (A) 66-70
% 8
IP.. X 3
CE
✔
(km/h) forw. 6 / rev. 3
m/s 2 < 2,5