En Original Instructions; Declaration Of Conformity; Specified Use; General Safety Instructions - Metabo STA 18 LTX Originalbetriebsanleitung

Original instructions

1. Declaration of Conformity

We, being solely responsible: Hereby declare that
these jigsaws, identified by type and serial number
*1), meet all relevant requirements of directives *2)
and standards *3). Technical documents for *4) -
see page 3.

2. Specified Use

The machine is suitable for sawing non-ferrous
metals and sheet steel, wood and similar materials,
plastics and similar materials. Any other use is not
permitted.
The user bears sole responsibility for any damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.

4. Special Safety Instructions

Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Ensure that the spot where you wish to work is
free of power cables, gas lines or water pipes
(e.g. using a metal detector).
Protect battery packs from water and
moisture!
Do not expose battery packs to naked flame!
Do not use faulty or deformed battery packs!
Do not open battery packs!
Do not touch or short-circuit battery packs!
Slightly acidic, flammable fluid may leak from
defective Li-ion battery packs!
If battery fluid leaks out and comes into
contact with your skin, rinse immediately
with plenty of water. If battery fluid leaks out
and comes into contact with your eyes, wash them
with clean water and seek medical attention
immediately.
During work, the workpiece must lay flat and be
secured against moving, e.g. using clamps.
Do not try to saw extremely small workpieces.
When sawing, the footplate must make secure
contact with the workpiece.
When interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material
until the saw blade comes to a complete stop. Never
attempt to remove the saw from the workpiece while
the saw blade is in motion or kickback may occur.
Do not switch the machine on while the saw blade is
touching the workpiece. Let the saw blade reach full
speed before making a cut.
When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If the saw blade
seizes, it may kickback from the workpiece when
the saw is restarted.
Keep hands well away from the sawing area and the
saw blade. Do not reach underneath the workpiece.
Remove chips and similar material only with the
machine at standstill.
Remove the battery pack from the machine before
any adjustments, conversions or servicing are
performed.
Danger of injury due to the sharp jigsaw blade. After
stopping work, the jigsaw blade may still be hot.
Wear protective gloves.
Risk of crushing during operation! Keep your fingers
away from the area of the saw blade tensioning
device (2).
Remove the battery pack from the machine when
not in use.
LED (9): Do not view LEDs directly through optical
instruments, LED class 1M, classified as per
DIN EN 60825-1: 2003, wavelength: 400-780 nm;
t =300 µs, 5 lm.
imp
Reducing dust exposure:
Some of the particles generated using this
power tool may contain substances known to
cause cancer, allergic reactions, respiratory
diseases, birth defects or other reproductive harm.
Some of these substances include: Lead (in paint
containing lead), mineral dust (from bricks,
concrete etc.), additives used for wood treatment
(chromate, wood preservatives), some wood types
(such as oak or beech dust), metals, asbestos.
The risk from exposure to such substances will
depend on how long the user or nearby persons are
being exposed.
Do not let particles enter the body.
Do the following to reduce exposure to these
substances: Ensure good ventilation of the
ENGLISH en
9