Product Description And Specifications - Bosch GKS 600 Professional Originalbetriebsanleitung

OBJ_BUCH-2756-001.book Page 14 Tuesday, January 19, 2016 2:29 PM
14 | English
Kickback is the result of saw misuse and/or incorrect oper-
ating procedures or conditions and can be avoided by tak-
ing proper precautions as given below.
 Maintain a firm grip with both hands on the saw and po-
sition your arms to resist kickback forces. Position
your body to either side of the blade, but not in line with
the blade. Kickback could cause the saw to jump back-
wards, but kickback forces can be controlled by the opera-
tor, if proper precautions are taken.
 When blade is binding, or when interrupting a cut for
any reason, release the trigger and hold the saw mo-
tionless in the material until the blade comes to a com-
plete stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is in mo-
tion or kickback may occur. Investigate and take correc-
tive actions to eliminate the cause of blade binding.
 When restarting a saw in the workpiece, centre the saw
blade in the kerf and check that saw teeth are not en-
gaged into the material. If saw blade is binding, it may
walk up or kickback from the workpiece as the saw is re-
started.
 Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag under
their own weight. Supports must be placed under the pan-
el on both sides, near the line of cut and near the edge of
the panel.
 Do not use dull or damaged blades. Unsharpened or im-
properly set blades produce narrow kerf causing excessive
friction, blade binding and kickback.
 Blade depth and bevel adjusting locking levers must be
tight and secure before making cut. If blade adjustment
shifts while cutting, it may cause binding and kickback.
 Use extra caution when sawing into existing walls or
other blind areas. The protruding blade may cut objects
that can cause kickback.
Lower guard function
 Check lower guard for proper closing before each use.
Do not operate the saw if lower guard does not move
freely and close instantly. Never clamp or tie the lower
guard into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the lower guard
with the retracting handle and make sure it moves freely
and does not touch the blade or any other part, in all angles
and depths of cut.
 Check the operation of the lower guard spring. If the
guard and the spring are not operating properly, they
must be serviced before use. Lower guard may operate
sluggishly due to damaged parts, gummy deposits, or a
build-up of debris.
 Lower guard may be retracted manually only for spe-
cial cuts such as "plunge cuts" and "compound cuts".
Raise lower guard by retracting handle and as soon as
blade enters the material, the lower guard must be re-
leased. For all other sawing, the lower guard should oper-
ate automatically.
1 609 92A 1RW | (19.1.16)
 Always observe that the lower guard is covering the
blade before placing saw down on bench or floor. An un-
protected, coasting blade will cause the saw to walk back-
wards, cutting whatever is in its path. Be aware of the time
it takes for the blade to stop after switch is released.
Additional safety warnings
 Do not reach into the chip ejector with your hands. They
could be injured by rotating parts.
 Do not work overhead with the saw. In this manner you
do not have sufficient control over the power tool.
 Use suitable detectors to determine if utility lines are
hidden in the work area or call the local utility company
for assistance. Contact with electric lines can lead to fire
and electric shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property damage or
may cause an electric shock.
 Do not operate the power tool stationary. It is not de-
signed for operation with a saw table.
 Do not use high speed steel (HSS) saw blades. Such saw
blades can easily break.
 Do not saw ferrous metals. Red hot chips can ignite the
dust extraction.
 When working with the machine, always hold it firmly
with both hands and provide for a secure stance. The
power tool is guided more secure with both hands.
 Secure the workpiece. A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand.
 Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
 Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should
be cut off and an appropriate plug fitted in its place by an
authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Products sold in AUS and NZ only: Use a residual current
device (RCD) with a rated residual current of 30 mA or
less.
Product Description and Specifica-
tions
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
While reading the operating instructions, unfold the graphics
page for the machine and leave it open.
Bosch Power Tools