Start Up; Operations - Kärcher SE 4001 Handbuch

Start up

Description of the Appliance
The scope of delivery of your appliance is illustrated on
the packaging. Check the contents of the appliance for
completeness when unpacking.
In the event of missing accessories or any transport
damage, please contact your dealer.
Illustrations on fold-out page!
Illustration
1 Motor casing
2 Carrying handle
3 Foam filter
4 Filter lock
5 Power cord with plug
6 Storage, power cord
7 Switch for suction (0 / I)
8 Switch for spraying (0 / I)
9 Release fresh water reservoir
10 Fresh water tank
11 Container
12 Swivel casters
13 Connection for the suction hose of the multi-pur-
pose vacuum cleaner
14 Connection spray hose
15 Suction hose
16 Handle
17 Surrounding air separator
18 Spray handle with spray lever
19 Spray hose, loose
20 Mounting clips (10x)
21 Suction tubes 2 x 0.5 m
22 Storage for suction tubes and accessories
23 Spray-ex floor nozzle for carpet cleaning, with hard
surface attachment
24 Spray ex hand nozzle for upholstery clean-
ing
25 Adapter for spray-ex manual nozzle for up-
holstery cleaning
* SE 4001 Plus
Additional vacuuming accessories
26 Floor nozzle with hard surface insert
27 Upholstery nozzle
28 Crevice nozzle
29 Filter bag
Before Startup
Illustration
 Remove the fresh water reservoir. Press the re-
lease and remove the tank.
Note:
The motor casing can only be removed if the fresh
water reservoir was removed first.
Illustration
 Remove the motor casing. For this, fold the car-
rying handle forward to unlatch the reservoir. Re-
move the accessories and swivel casters from the
reservoir.
Illustration
 Turn the container, press in the steering roller in the
openings at the base of the container till the end-
point.
Illustration
 Turn the motor casing around and attach the foam
filter to the filter basket.
 Insert the filter cover and turn to lock.
 Install the motor casing. Pull up on the carrying
handle to lock.
Illustration
 Install the fresh water reservoir. Insert the bot-
tom part first and then press toward the top on the
motor compartment to check if it is locked in.
Illustration
 Slide the spray handle onto the handle until it locks
into place.
 Attach the spray hose of the spray handle to the
suction hose using 7 mounting clips.
 Attach the suction hose and the spray hose to the
connectors on the appliance.
Note
: Press the suction hose tightly into the connector
to lock it into place.
Illustration
 Connect the suction tubes and attach to the handle.
 Insert the loose spray hose in the spray handle and
attach to the suction tubes using the 3 included
mounting clips.
 Attach the floor nozzle to the suction tubes and in-
sert the spray hose into the floor nozzle. Rotate the
exterior safety lever and lock the spray hose into
place.
The appliance is now prepared for wet cleaning.
Wet cleaning with the spray-ex manual nozzle for
upholstery cleaning *
Illustration
8.2
 For the installation of the spray-ex manual nozzle
the enclosed adapter must be connected and
locked between the spray-ex manual nozzle for up-
*
holstery cleaning and the handle.
* SE 4001 Plus
*
ATTENTION
Always work with an inserted foam filter - during wet
cleaning as well as wet and dry vacuum cleaning.
Wet cleaning of carpets/hard surfaces
ATTENTION
Check the object to be cleaned prior to using the appli-
ance in an inconspicuous place for colour fastness and
water resistance.
Do not clean water-sensitive floor coverings such as
wood floors (the moisture could penetrate and damage
the floor).
Note:
Warm water (max. 50°C) will increase the cleaning ef-
fect.
Wet cleaning of carpeted floors
 With spray-ex floor nozzle without hard surface at-
tachment.
Please only use the carpet cleaner RM 519.
Wet cleaning of hard surfaces
 With spray-ex floor nozzle with hard surface attach-
ment.
Slide the attachment for hard surfaces onto the side of
the spray-ex floor nozzle. The squeegee points towards
the front, the brush strip towards the back.
– 8
EN
8.1

Operations

15