Bosch PPS 7S Originalbetriebsanleitung Seite 33

OBJ_BUCH-1259-004.book Page 33 Thursday, November 6, 2014 10:45 AM
30 Extension plate for the universal guide
31 Guide rail for the universal guide
32 Detent override for adjustment of mitre angles
33 Wing bolt for locking mitre angles
34 Wing bolt for locking the fence 36
35 Angle stop with scale for mitre angles
36 Fence on the universal guide
37 Wing bolt for locking the guide rail 31
38 Rotary knob for locking the universal guide
39 Bottom plate
40 Battery lid
41 Laser unit
42 Fastening kit for "laser unit"
43 Fastening kit for "blade guard"
44 Laser on/off switch (for marking of cutting line)
45 Fastening screw for laser housing
46 Laser housing
47 Thumbwheel for positioning of laser
(flush alignment)
48 Fastening kit for "table extension"
49 Support leg of the table extension
50 Allen screws of the upper fastening plate for support leg 49
51 Rotary knob for fine adjustment of the table-extension
height
52 Rotary knob for locking the table extension
53 Support tongue for the fence 36
54 Lower saw blade cover
55 Cleaning flap of the lower saw blade cover
56 Spindle lock
57 Hex socket screw (size 6 mm) for mounting of saw blade
58 Exterior clamping flange
59 Interior clamping flange
60 Screws for fastening of the riving knife
Accessories shown or described are not part of the standard deliv-
ery scope of the product. A complete overview of accessories can
be found in our accessories program.
Technical Data
Pull Push Saw
Article number
Rated power input
No-load speed
Reduced starting current
Constant electronic control
Laser type
Laser class
Weight according to
EPTA-Procedure 01/2003
Protection class
Maximum workpiece dimensions, see page 38.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Bosch Power Tools
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Tooth thickness/setting, min.
Mounting hole diameter
Noise Information
Sound emission values determined according to
EN 61029-2-1.
Typically the A-weighted noise levels of the product are:
Sound pressure level 97 dB(A); Sound power level
110 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 61029-1, EN 61029-2-1, EN
60825-1.
EC Type Examination No. MSR 1036 by notified testing agen-
cy No. 0366.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker
Executive Vice President
Engineering
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 22.09.2014
Assembly
 Avoid unintentional starting of the machine. During as-
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
PPS 7S
3 603 M03 3..
Delivery Scope
W 1400
-1
min 4800


nm 650
Before starting the operation of the machine for the first time,
mW
< 0.39
check if all parts listed below have been supplied:
1M
– Pull Push Saw
(Mounted: Saw blade 28, insert plate 5)
kg 23.2
– Universal Guide 1
/II
– Rotary knob 38 for locking the universal guide
– Laser unit 41
– Fastening kit for "laser unit" 42
(Allen screw, nut)
English | 33
mm
mm
mm
mm
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
Please also observe the representation of
the delivery scope at the beginning of the op-
erating instructions.
1 609 92A 0VR | (6.11.14)
190
1.6–2.0
2.6
30